tv remote caddy 3d models

Apple TV 4th generation remote caddy. ...Screw this to your wall and never lose your remote again.

apple tv remote holder for 2021 remote silver with mic button on side needs the thick back end to not scrape remote with screw and possibility for screw cover if wanted

needed a way to keep my tv and fire tv remotes together and tidy. designed this concept. Works well. No need for supports, printed this with 3DQF filament @ 2.8 with a 0.6mm nozzle. ... Took about 5 hours to print @ 35mm/s

needed a way to keep my tv and fire tv remotes together and tidy. designed this concept. Works well. No need for supports, printed this with 3DQF filament @ 2.8 with a 0.6mm nozzle. ...Took about 5 hours to print @ 35mm/s

This is a caddy for the Amazon Fire TV remote. My kids kept losing the remote because it's small (fits between couch cushions, under the chair, etc.) and black (hard to see). I solved both problems by encasing the remote in a brick of...

If you need to hold less remotes and build a less massive caddy, just slice off the ends to make it either a four remote caddy or even all the way down to just two. ... The mounting holes are only designed for four or six though, but 3M makes some...

reupload of my sanyo remote holder as i uploaded it before the contest was made. 

I made this to hold the remote control for my Xfinity remote and provide a charging dock for the Apple TV remote. For me the inclusion lightning cable required a bit of super glue to keep it in the dock while docking/undocking the apple remote. ... ...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/94tu85YIGO1

Remote control holders including Apple TV remotes (4th and 5th Generation). I added a slit to allow vertical as well as slanted storage for the Apple TV remote. No support is needed. ... The 5th Gen stands are coming.

Remote caddy with some different options for attachments.

TV Clicker caddy that screws to a wall outlet

We don't have an end table or a coffee table, so they were usually either lost in/under/behind the couch, or sitting on top of the entertainment center next to the TV (defeating the purpose of a remote control). ...So I made a pretty simple wall mounted...

remote control caddy for various sized remotes (see pics for relative sizes) printed w/ PLA. I used a brim, but you may not need it. ... No supports needed.

This is a remix of the Remote control caddy by CosmicBeyond. ...This version is based on the small caddy, but have more extensions to put pens and other stuff into it.

This is a remix of the Remote control caddy by CosmicBeyond. ... This version is based on the small caddy, but have more extensions to put pens and other stuff into it.

I spent most of my time tuning the fit of the remotes so that it was snug but still easy to insert and remove them. In the bottom of the caddy there are pockets for six 608 bearings for some added weight to keep the caddy stable and prevent it...

This caddy holds up to 6 remotes, each of which can be up to about 50mm (2") wide and 25mm (1") thick.

In my bedroom my remotes were always getting moved around, lost and more. ...I wanted to make a caddy that would be strong and durable but use minimal material so this is what I came up with.

I wanted to make a caddy that would be strong and durable but use minimal material so this is what I came up with. ... Instructions Print and use anyway you want, you may need to turn 45d to print...

This is a remote caddy that attaches to my lamp post. This holds my Samsung watch charger, headphones, and backpack as well. Orientation depends upon if you decide to print with inserted square 3mm nuts. ---> There are 3mm square nut slots cut...

... a sharpie to help it stand out. When I printed, I had the flat bottom section on the bed in the orientation that has the word "TV" upright. ...I turned on supports on Cura with zig-zag at 5% to support the upper flange that attaches to the table.

http://www.thingiverse.com/apps/customizer/run?thing_id=209497 Instructions Using the following options: font_spacing = 2 num_rows = 1 remotes_per_row = 2 tallest_height = 110 smallest_height = 45 compartment_depth = 35 wall_thickness = 2 front_text...

http://www.thingiverse.com/apps/customizer/run?thing_id=209497 Instructions Using the following options: font_size = 12 tallest_height = 60 compartment_depth = 30 front_text = num_rows = 1 font_spacing = 2 compartment_width = 59 remotes_per_row = 3...

I kept losing the remote to my back porch lights. I had spare wall plate space so I designed this thing. The first version's screw holes didn't match, so I had to move the holes 13mm closer to each other. ... Who knew light switch plates weren't...

Just something I made for a friend so he could put his remotes, glasses, and headset which is the older style walkman earphones on his laptop desk by his bed. Printed it on ender-3 with wood filament came out very nice even on course settings took 17...

TV Remote

TV Remote

TV Remote

TV remote CAD model