tv riser for soundbar 3d models

Si vous n'avez pas d'imprimante 3D et que le produit vous intéresse, rdv sur Etsy ou vous pourrez passer commande :...

I needed to raise the height of my Philips 65 inches TV to install a soundbar above. I created a tunnel and a notch for cable management and to reduce some PLA The stl file was designed for right support with notch inside but you can apply a mirror...

So I wanted to place my soundbar directly under my standing flatscreen tv but it did not fit and came up with this. I did put some sheets of rubber (cut from an old bicycle inner tube) under it to make it more stable and less likely to shift. ...

A tilted riser for the XiaoMi 33" TV Soundbar. Has an angle of 10°. Perfect if you have a lower TV setup and want the soundbar point directly at you :) Fits directly in the socket. ...Just peel off the rubber feet, place them under the soundbar and...

We bought a Sonos Soundbar and it didn't fit under the tv so I made these feets

... loops that snugly fit my HDMI and power cables. The dimensions of the inner rectangle are 101mmx60mm so if you have the TV but do not have the same soundbar this may work for you. ... **TV:** Samsung 65RU7100 4K **Soundbar:** Samsung HW-Q60R

Support designed for Samsung Soundbar HW-K360 to fit on stand holes of TV Samsung 49KS7000. ...It's a very tight fit, so it holds the soundbar weight without problem.

Support designed for Samsung Soundbar HW-K360 to fit on stand holes of TV Samsung 49KS7000. ...It's a very tight fit, so it holds the soundbar weight without problem. Category: Household

Dieser Halter dient zur Erhöhung des Philips TV's, damit die Soundbar nicht mehr im Bild ist.

I got myself a cheapass Samsung soundbar and needed a way to elevate my cheapass Phillips tv to allow seing the image as well as hearing the sound well. You can use draft file to customize it for you or make a different style base. I decided that...

Simple riser for JBL SB250 Soundbar to get over the top of a TV base. May work on other makes & models. 1.875" (47.625) dia., .625" (15.875) high. ...200c extruder, 55c platform.

LG Television pedestal riser for soundbar positioning.

I decided the best way to attach it was to print a pair of brackets that would snug fit the soundbar between them using the existing screws and holes formerly used for the legs. v4 still isn't a perfect fit with the complex geometry they felt was...

Print 2 clamps/holders for the soundbar. ...

I remixed the soundbar support mount from https://www.thingiverse.com/thing:3046887 to fit my LG soundbar (hole 89mm x 57.15mm estimated) It gives little extra room for the soundbar. ... I printed at 101%

Requires two additional screws to mount the soundbar onto the part (in addition to the two screws to mount the whole thing to the TV). I initially designed it to where a part of the print fit into the back of the soundbar and no screws were needed,...

I designed and printed this TV top-holder for my Samsung Soundbar (HW-J250) to sit on my 2009 Samsung LCD TV (don't know the model). Decided to try and make it from scratch in Sketchup, but failed miserably on the curves! Found benzol's Thing...

I designed and printed this TV top-holder for my Samsung Soundbar (HW-J250) to sit on my 2009 Samsung LCD TV (don't know the model). Decided to try and make it from scratch in Sketchup, but failed miserably on the curves! Found benzol's Thing...

I created this as I could not find a soundbar mount to fit the top of my Sony television. ... This attaches to the Sony X700E television (TV width: 12mm) This fits the Sony RT-3 sound bar (height: 53mm / width: 70mm)

My TV stand is only so big, and my old LCD TV has a HUGE baseplate, so I had to raise my new soundbar in order to clear the stand and have room for a HDMI switcher. 3D printer to the rescue! This was meant for Vizio soundbars with 50mm square...

... and mouse cables to be fished under the bar itself. I have these risers sitting on the rubber feet of the soundbar and it works perfectly for my needs. I doubt many of you have the same setup, but I put in here for those few that may. ...Enjoy!

Riser for 2019 model LG 43UM7300PUA TV. Wanted something to lift it up higher than my Energy Center-channel speaker so that it won't block the screen nor the IR receiver. ...

If you have soundbar and don't have a place where to put it, the best place is on top of your TV! ... This holder is light and good even for small TV frames, can hold your soundbar.

Recently purchased a Vizio soundbar/ subwoofer system and wanted to mount the soundbar to our 55" Vizio tv so that it would be directed at us when we move the tv away from the wall. Because the tv stand inserts are near the edge of our tv and the...

This was designed for a Vizio TV and Vizio Soundbar. ...Should work with most tv's that are at least 40mm thick and a sound bar that is no thicker than 80mm.

Bose Solo 5 mount for this tv stand: https://www.amazon.nl/-/en/gp/product/B07XRJ347J/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 The bolts feed through the two parts into the soundbar mounting threads. ... Onshape document:...

Recently purchased a Vizio soundbar/ subwoofer system and wanted to mount the soundbar to our 55" Vizio tv so that it would be directed at us when we move the tv away from the wall. Because the tv stand inserts are near the edge of our tv and the...

The STL is set up for my Samsung soundbar: Width: 60.2 mm Height: 55.2 mm and Hisense LCD TV: Width (at top): 25.5 mm Width (at bottom): 29.5 mm I have included the sketchup file so the dimensions can be modified to suit. With my printer I have spent...

Phillips 55OLED934 TV Angle Soundbar Holder Print instructionsNo supports needed

This probably won't be of any use for anyone else unless you have the exact same model of TV + soundbar as me, but hopefully this will give you some inspiration if you want something similar. I included the Sketchup files if you want to work off...