tweaker cam 3d models
18480 3d models found related to tweaker cam.thingiverse
Tweaker Cam Mount 25° Überarebitete version 5mm Löcher und 0,9mm Höher
thingiverse
Tweaker Cam Mount 30° Überarebitete version 5mm Löcher und 0,9mm Höher
thingiverse
I did this 20deg fatshark FPV Cam mount for my Tweaker 180 miniquad. Suited for the 600TVL Fatshark and similar cams. Have fun with it. Post-Printing Instructions I print this with 100% infill in...
thingiverse
tweaker shendrone pico cam adjustable mounting bracket
thingiverse
This mount is designed for the Shendrones Tweaker 180 using this 28x28mm 600TVL camera: http://www.surveilzone.com/28x28mm-Sony-Super-HAD-CCD-600TVL-Mini-Camera-250-Frame-g-1381 Camera mounts to part using M2.2 self tapping screws. ...Print Settings...
pinshape
SummaryThis mount is designed for the Shendrones Tweaker 180 using this 28x28mm 600TVL camera: http://www.surveilzone.com/28x28mm-Sony-Super-HAD-CCD-600TVL-Mini-Camera-250-Frame-g-1381 Camera mounts to part using M2.2 self tapping screws.Print...
thingiverse
This mount is designed for the Shendrones Tweaker 180 using this 28x28mm 600TVL camera: http://www.surveilzone.com/28x28mm-Sony-Super-HAD-CCD-600TVL-Mini-Camera-250-Frame-g-1381 Camera mounts to part using M2.2 self tapping screws. Print Settings...
thingiverse
This is a Pico Cam FPV mount for the Tweaker 180 quad. Using the stock front standoffs the mount is secured to the front of the quad. There are supports for the cam to keep it from moving fore and aft, it is a snug fit. A tie wrap is used to keep it...
cults3d
... up in a crash. On one hand, not bad because the cam will tear off rather than smash. On the other, cam will be torn off and you get to search for it. ... I needed a lightweight, space-saving way to mount a Runcam HD on an already overweight copter.
thingiverse
... up in a crash. On one hand, not bad because the cam will tear off rather than smash. On the other, cam will be torn off and you get to search for it. ...I needed a lightweight, space-saving way to mount a Runcam HD on an already overweight copter.
thingiverse
This is a 12mm camera mount for the ShenDrones Tweaker 180mm quadcopter frame. The angle is 17 degrees. This was the camera I used: http://www.banggood.com/600TVL-8_0MP-14-2_8mm-CMOS-FPV-170-Degree-Wide-Anlge-Lens-Camera-PALNTSC-p-984345.html, but...
thingiverse
Shendrones Tweaker accessories. ...Print in TPU and glue with Foam Tac.
thingiverse
A landing foot designed specifically for the standard Tweaker. ...It's 2mm in diameter wider than the motor mounts on the Tweaker arms, but really this would fit most any 18xx arm with a 12x16 bolt pattern.
thingiverse
Protection for Shendrones Tweaker FPVA Edition. ...Arm guards are either glue-on or screw-on, the screw-on version allows two motor screws to pass through so you have two screws that are solidly on the carbon.
thingiverse
Accessories for the new Shendrones 5" Tweaker. ...Arm and nose guard can be in ABS, cam mount has to TPU.
thingiverse
Cam, VTX and antenna mounts for the Connex Prosight in a Shendrones Tweaker 5. TPU only, everything needs to flex. ...Read more about it at http://www.shendrones.com/prosight-tweaker
thingiverse
Cam mount, tail, armguards, Session mount for Tweaker 5". ...TPU.
thingiverse
A small and light 30° mount for the Xiaomi Yi on the Tweaker 180 of Shendrones
thingiverse
TPU battery pad for Shendrones Tweaker. ...SMA and bolt holes are countersunk so mirror if you're running the top plate the other way.
thingiverse
Hey guys, this is my Cookie Cutter of the tweaker. I also have a cutter for the krieger. ...;-) visit: racequadgear.de
thingiverse
Antenna holder I came up with to allow direct mounting of VTX in cutout on the tweaker. This is for the latest top plate for the Tweaker. I have a non extended version for the old original I'll upload later. ...Print Settings Printer: ...
thingiverse
... first version of the mount I made. It should in theory work with all GoPros as they all use the same base mount. It fits the tweaker and the gopro and everything comes together well, but as of yet I haven't flown it or more importantly, crashed it.
cults3d
Closes off the back of the tweaker with an XT60 cutout and circle for an SMA extension and antenna. The sides have mounting holes for addressable LED's bought at Readytoflyquads.com (http://www.readytoflyquads.com/rtfpixel-stick-8x-rgb-leds). Picture...