two trees sapphire 3d models

Utilisation des vis d'origine pour "Origine chaine" et "Fixation laser" Use of the original screws for "Chain origin" and "Laser fixing"

The spool holder included with the Bluer Plus is too small. Use this one instead. Fits up to 85mm wide spools. No supports needed. ... Use 3 shells and 50 percent infill

original: https://www.thingiverse.com/thing:4562652 step motor deliği büyütüldü, step motor bölümü genişletildi civata bağlantı delikleri yerleri ayarlandı,

205 / 65 50MM/S NORMAL DESTEK/SUPPORT BLUER PRINT READY SMP

https://www.youtube.com/shorts/q9eDR5H6suQ

Offset : X = Y =

Modification for direct extrusion with bmg and factory motor, remixed with the capacitive sensor in a single piece, easy to assemble.

The human interface enables precise calibration of the Z-axis limit switch. ...High-quality M3 bolts are utilized.

Supports: Yes Infill: %100 Resolution: 0,20 Filament : Petg or Pla (petg more better)

Using the printer's original extruder, position adjusted, holes positioned accurately, screw heads countersunk. The yellow washer because of My laziness .. :). The screw was too long. ...:)

How to printPlease! print in the same direction like fourth foto. ...I printed PLA and its works good.

Needed to mount my engraver to the table and elevate it for large projects.

Just though of sharing because the metal piece not all in good place so everytime have to bend or cut, now just design and replace solve the issue!

I deactivated the filament sensor of my Bluer and instead installed a filament guide. ...You can use the original screws that fastened the filament sensor and a third screw for the pulley.

I completely revamped the filament guide by Wiper, incorporating larger holes to allow for easy movement and precise alignment with the runout sensor. I also integrated support for the cabling, eliminating unnecessary sagging. ...Typically, I design...

I found it difficult to turn the thread feed clamp bolt. Therefore, I decided to make a convenient wheel for it in the form of a crane. ...I was inspired by the VALVE logo at the beginning of the Half Life game) installation: preheat the heat gun to...

Spacer for the bottom cover of the printer, to get cables in or out, better cooling, etc.

Supports: Yes Infill: %100 Resolution: 0,20 Filament : Petg or Pla (petg more better)

<p>Use stock motor, don't need to adjust firmware or steps<br>Use 12mm screws<br>Adjust retraction only<br>Print with PETG or ABS 0.2 layer height&nbsp;</p>

There's people how don't give a shit about anything, on the other side is Turdrim who shits on everything specially on battle days. ... He never leaves his weakly issue of the Grudge magazine.

If like me you damaged your original protection, here is this replacement, just need to buy 4x4 magnets on ali or get the old ones.

Vibrant, stylized pine trees rise from minimalist backgrounds, adorned with delicate, hand-crafted textures that evoke a sense of rustic charm.

This is a small change to the original posted by G4Cab. I removed the Chain STL's, they are just not worth it. I lengthened the Cable Management for the 10x20 Chain setup and combined the cable management for the 7X7. You can purchase a 7x7 and 10x20...

This is a small change to the original posted by G4Cab. I removed the Chain STL's, they are just not worth it. I lengthened the Cable Management for the 10x20 Chain setup and combined the cable management for the 7X7. You can purchase a 7x7 and 10x20...

Reinforce your skills through training that incorporates Fusion360.

Customized version of https://www.thingiverse.com/thing:834725 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=834725

Priceless Plastic Gems