tymora d&d 3d models

Tymora is the goddess of luck and good fortune in Dungeons and Dragons. This prop was created with players in mind who would later redeem it. Before printing, I scaled the model to approximately 4.5cm in length. Edit: The FDM model has been revised...

This is a precise replica of the TSA9840 Class D Amplifier 20W x 2, ideal for crafting your own custom audio equipment.

Simple audio rack designed to hold two (or more) D-Class amps like the Aiyima A07Rack main pieces and side supports should be printed right side up, the top though should be printed upside down to limit the risk of the interlocking holes becoming...

d.Va's AMP TV logo sports a dynamic design that perfectly captures her South Korean personality and gaming style.

This is a 15 D-Sub connector with a back-shell

Crude model of a "TDA8932T 35W CLASS D" monophonic amplifier module measured from an actual part. ...These boards have slightly different measurements when sourced from different manufacturers, so measure your actual part before committing to mounting...

d

D

d

I'm a Text Rewriting Bot, here to assist you. ...What's the text you'd like me to rewrite?

... ...It has been published in over 30 countries worldwide and has spawned numerous novels, anime series, and films. The series follows the story of D, a half-human, half-vampire who hunts down his own kind to protect humans from their evil influence.

http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: basethickness_percent = 0% baseheight_percent = 0% wall = true base_radius_add_percent = .1% textstring = D textheight = 40 points RoundedBase =...

https://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: textsize = 25 RoundedBase = 0 baseheight_percent = .33 base_radius_add_percent = .1 basethickness_percent = 0.1 fontname = Bowlby One SC wall =...

www.thingiverse.com/apps/customizer/run?thing_id=1343760 Instructions Using the following options: Letter = D Font Y Position = -9.5 Circle Height = 2 Circle Radius = 16 Hatch Thickness = 1 Font X Position = -7 Hatch Angle = 315 Hatch Spacing = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=139461 Instructions Using the following options: TextSpacing = 10 TextRelief = -10 Text = D ManualThickness = 1.75 build_plate_manual_y = 100 build_plate_manual_x = 100 ColumnSpacing = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Using the following settings: Shift Font Size By: 0.07 Percent Text Height: 15 Units Base Thickness: 0.1 Percent of Overall Base Dimension Base Height: 33 Percent of Entire Structure...

http://www.thingiverse.com/apps/customizer/run?thing_id=408698 Instructions Using the following options: text_thickness = 3.5 text = D pencil_hole = 1 pencil_width = 15 letterspaces = [0,59,52,50.5,52,50,50,50,50,50,50,50,50,50,50] pencil_sides = 6...

http://www.thingiverse.com/apps/customizer/run?thing_id=139461 Instructions Using the following settings: Font Height = 90 points Text Input = "d" Font Type = write/Letters.dxf Manual Radius = 9.5 mm Number of Columns = 1 Manual Thickness = 1.75 mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following settings: Base Roundness: Set to Rounded Base 1 Text Size: 35 units selected Font Name: Lemon font is chosen Base Height Percentage: Base height...

http://www.thingiverse.com/apps/customizer/run?thing_id=139461 Instructions Using the Following Options: Column Count: One Text Height: Ninety Units Font Selection: Write/Letters.dxf File Manual Radius Adjustment: Nine and a Half Units Manual...

http://www.thingiverse.com/apps/customizer/run?thing_id=139461 Instructions Using the following options: TextRelief = 10 Above Norm Number of Rows = One at a Time Font = Write or Orbitron DXF File Build Plate Manual Y-Axis = Hundred Percent Build...

... high. Loop font chosen for use is Chewy. Letter "D" is being displayed as part of the text sequence. Loop character is "o". Text loop y-position has been fixed at zero units. ...Four-unit height adjustment for five-letter words has been applied.

Hey! ...Just print it and take a rope. Bind them together aaaand go! Do it soft with TPU, so you will learn Nunchakus without pain! xD I hope you like my design! =) D.D.D. Follow Ig. ...--> @3d_4u_prints

Sample of a status ring for charmed to use in D&amp;D! ...More status rings coming soon!</p>

Figurine for D&D

D&D mini wizard

Dragonhorse D&D

I designed this for a friend who plays D&amp;D Print instructionsPrint at 0.2

The D&amp;D Logo to customise your print.Like I did on my dice box.Printed with 100% infill

Basic D&D Dungeon tiles