ublox gps 3d models
7733 3d models found related to ublox gps.grabcad
Simple Ublox GPS it's part of a bigger project, I gonna upload more parts soon.you can find it...
thingiverse
Simple 3-part 3dr uBlox GPS Case for use with reflector Instructions This is a simple three-part 3dr uBlox GPS case. I was looking for an easy way to fit a reflector under the GPS to improve performance. ...Use thin metal film between bottom (shield)...
grabcad
This is 3D printer friendly enclosure for Jdrones Ublox GPS. Cable hole is sealed using normal furniture foam rubber with sticker. Tape is Gorilla "FOR THE TOUGHEST JOBS ON PLANET EARTH™" tape. ... 3Drobotics connector position is different and...
thingiverse
The GPS I'm using is a FuriousFPV UBLOX GPS. The GPS measurements are 20mm x 18mm x 7mm. ... There are two versions: - v1 - tiny holes for zip ties - v2 - reinforced triangle at rear Check out my [Flying Squirrel](https://flyingsquirrel.ch/)...
thingiverse
Instructions This is a small case I made for the the GPS receiver base on a Ublox NEO-6M, as shipped by Unmanned Tech in the UK. Update 11/08/2014: Added a bit more space around the parts to allow for slight over-printing problems stopping the lid...
thingiverse
Replacement mast mount for the 3DR uBlox GPS mast. Instructions To replace a damaged mount, slide the old pin out carefully and the mast should pop out. Slide the mast into the printed base, line...
thingiverse
Armattan Marmotte MMCX and UBLOX GPS Holder. This fits in the rear hangers and provides a little slot for a MMCX antenna cable to rest in. The GPS unit slots into the upper box and the cable goes into the drone body. The battery protects it from...
thingiverse
Simple mounting for M3 threaded rod for your UBLOX NEO M8N
thingiverse
Customized version of http://www.thingiverse.com/thing:415391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=415391 Instructions Using the following options:...
thingiverse
A UBLOX M8N GPS mount for your Bannilite! ... Get your UBLOX M8N from ReadyToFlyQuads: http://www.readytoflyquads.com/micro-ublox-m8n-gps-w-18x18x Get your Bannilite here: http://falconmultirotors.com/bannilite.html
thingiverse
This is 30.5x30.5 a stack-able mount for a mini m8n ublox gps. ...The mini ublox fits snugly in the mount but there is a pass-thru for a zip-tie if needed.
grabcad
Ublox 6M High Precision RC Quadcopter GPS Module With Compass GPS Antenna
thingiverse
VirtualRobotix Ublox-M8 GPS case Instructions Milled starting from a 8mm thick sheet of ABS. ...The processing on the two sides requires the use of a template to clamp the workpiece (an ABS chunk with 4 holes)
thingiverse
... Link Antenna Mount designed by itsqv.com. The base can be glued into the pocket (will require slight trimming of foam at front of pocket) and the cover will securely hold the Micro Ublox and capture the Dragonlink Antenna wire and hold it in place.
thingiverse
When I added GPS to my Flame wheel I thought about adding a mount but then decided integrate it into the plate. It puts the GPS 4 cm above the plate. Print Settings Printer: Pruse i3 MK2 ...
thingiverse
https://www.readytoflyquads.com/mini-ublox-6m-gps-w-35x35mm-mounting-backplane-and-compass I had bought this particular model hoping that it would still pick up sat's while stack mounted. However as expected the carbon fiber blocked almost all sat...
thingiverse
3DR now do an all-in-one model but I have an APM2.5 and separate UBlox GPS and HMC5883L Magnetometer Circuit boards. So I made this housing for them. It has an arrow on the side so you know which orientation is forward, and if you print in clear you...
thingiverse
Case for an Ublox neo 6/7/8 gps with separate antenna. ...Stl file prints all 3 parts at once, no support needed.
thingiverse
Holder to GR-BD*GPS*COMPASS with 50x50 M3 holes Put a stripe over the gps, there are aligners for it. Lay it down as shown on the first picture when printing. ... So that the holes with m3-threads are facing up.
thingiverse
A Unify SMA + UBLOX M8N GPS mount for your Raggio! ... Get your UBLOX M8N from ReadyToFlyQuads: http://www.readytoflyquads.com/micro-ublox-m8n-gps-w-18x18x
thingiverse
This is a mount box for Ublox NEO6M GPS GY-GPS6MV2 module. ...
thingiverse
Made to fit this micro Ublox M8N GPS unit to your Ranger or any surface with enough area to mount https://www.readymaderc.com/products/details/rmrc-mini-gps https://www.racedayquads.com/products/micro-ublox-m8n-gps-glonass
thingiverse
This is a mount that i designed to hold a Ublox M8N GPS unit to a mini-quad battery strap. Print with TPU as the material. ... 3/25/19 - I have added a few other variation per user requests.