udoo bolt v3 3d models
132717 3d models found related to udoo bolt v3.
thingiverse
This case is designed for the UDOO or Arduino microcontrollers, which can be held in place for the http://rovjacobsnotes.blogspot.com project. The ABS material makes it possible to glue different sensor mounts together using acetone. An air pocket...
thingiverse
This is my latest design for a 3D-printed case to encase the Udoo 7" touchscreen module. V2.1 has been finalized on the front, while V2.2 awaits final approval on the back panel and kickstand component. Initial prototypes are printing flawlessly and...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
cgtrader
Maruzen M1100 bolt ejector plate v3 - beware some holes require re-drilling, which depends entirely on the specific printer being utilized.
thingiverse
This is a Frankenstein remix of the following two dial indicators: CR-10 https://www.thingiverse.com/thing:2412647 CR-10 v3 https://www.thingiverse.com/thing:4591857 It was noted that the v3 one was a bit too loose, so I combined the one from the...
grabcad
Introducing a prototype for an upcoming Arduino iteration Submitted by the AI text spinner. ...The main goal is to provide a fresh perspective on the original sentence without adding any extra information or links, keeping it concise and within 60...
grabcad
Version 3.03 — Previous version: AKM Lightweight Bolt Carrier with Titanium Charging HandleОблегчённая затворная рама АКМ (Сайга, ВПО) с возможностью установки левой рукоятки перезарядки. Версия 3.03Основные отличия:• Более технологична • Уменьшено...
thingiverse
Hold upright q2ok's UDOO x86 3D printed case to enable the case to stand on its own end.
thingiverse
After more than a year of utilizing the Udoo x86 Ultra as a compact media solution for the living room, the small fan that came with it became an increasing nuisance. To eliminate the noise but still provide sufficient cooling, I simply designed a...
thingiverse
This product features a monitor stand specifically designed for UDOO devices, and comes with M3 screws in quantities of ten, M3 nuts for four, as well as M4 washers and M4 screws, totalling twelve M4 screws, all provided in quantities of four.
thingiverse
Assemble the Udoo Quad case with easy snap-together design. Leave space on top for accommodating 1 module; extend sides if needed. Share your enhancements by reaching out via email in the artwork. Use is permitted for personal purposes, but consult...
thingiverse
I decided to revise the first version of this project without including the ability to turn on your Udoo X86.\r\nSo, I simply drilled a 3mm hole in the case right above where the power button is located on the board and installed this small...
thingiverse
This creation was crafted using Tinkercad's powerful tools. ...Make your desired changes instantly at https://www.tinkercad.com/things/9oAbEyyz1Ej.
grabcad
A hexapod structure designed to work with the UDOO board and Dynamixel RX28H servo motors is available.