ultem 9085 3d models

Customized version of https://www.thingiverse.com/thing:2491884 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2491884

Alternate ULA Loading Bracket in Ultem 9085

First optimization test with ULTEM 9085 and the given targets.

CAT P-clamp

Mass: 0.07878 lbVolume: 1.62739 in^3Density: 0.04841 lb/in^3Material: Ultem 9085

mass - 0.043 lb / 19.5 gvolume - 0.89 cubic inchesULA bracket made of ULTEM 9085

Density 1340 kg m^-3Mass 6.4057e-002 kgVolume 4.7804e-005 m³Load 2668.9 NMATERIAL ULTEM 9085

This is my entry for the ULA Rocket support bracket challenge.A 3d printed bracket made of Ultem 9085.

Bracket designed for ULA rocket to be additively manufactured using Ultem 9085.Mass = 0.079lbVol = 1.622 in3Max Stress = 3,407psi

A support bracket for the Atlas V payload fairing. ... Designed to be 3D printed in Ultem 9085 with a mass of .16 pounds.

Ultem 9085 ULA Rocket Bracket - Payload FairingEnclosed Step and IGS files, Renderings of part and part with shell, pallet, hardware, and tool interfaces. ... Description of part, Mass, Volume, Stress PDF's.

Further development of my Ultem(R)ate Bracket B1.Using common 3D printing features to reduce mass of unstressed but thick parts (bosses).Stresses all less than 4500 psi, singularity/stress riser in FE model (due to contact between bolt and bracket)...

... points. Also, use thick walls to avoid leakage of fluids. Safe 3D printing materials for food contact (FDA approved): Ceramics PLA without additives PET, PETG / T-Glass ULTEM 9085 Polypropylene Natural grade Nylon 6 & 6.6 (without additives) PEEK

Material: Ultem 9085 Weight: 0.0783 lb / 35.52 g300 lb loads were placed at each vertical bolt holes, for a total of 600 lb. Pin constraints were used on the four attachment points. ...Pin constraint does not allow displacement in the X, Y, Z...

-avoiding stress concentration by removing sharp edges-simple and easy for installingsuggested material other then ultem 9085 carbon fibers calculations:bending stress 510 psi with f.o.s about 4 second moment of inertia = .5^4 inchvolume 91.09 cubic...

This is my second entry to the ULA Rocket Hardware Challenge.Unlike the previous entry, focus to preserve the overall shape of the original part was shifted to further reduce mass, increase rigidity, while maintaining manufacturability with minimal...

Entry for the ULA Rocket Hardware Challenge.The part design had the following requirements:-Maximum part weight: 0,046kg/0.1lb-Minimum wall thickness: 1mm/0.040in-Ultimate load: 2670N/600lb-Manufacturing method: FDM-Material Ultem 9085Aside from...

It has plenty of ribs and fillets to minimize stress concentrations.It harnesses the advantages 3d printing vs 5 machining.actual mass = 0.10 lbsvolume = 2.161 cubic inchesMaximum part weight: 0.1 lb (OK) Minimum wall thickness: 0.040 inches...

This bracket is made up of the Ultem 9085 ( resins are synthetic polymers include polystyrene resin ) . It is one of the most efficient research for the space and it is prepared by all the specification noted in the paper challenge. ...It is...

ULA Rocket Hardware Challenge--------------------------------------------------------The set parametersThe set density of bodies of Rou = 0.000134 g/mm3Material of bodies Ultem 9085 Density of material of bodies of Ro of =0.000134 g/mm3Calculated...

This bracket meets all the requirements asked by ULA for this challenge : - Minimum edge distance surrounding all bolt holes shall be 2 times the diameter of the bolt hole. - Maximum part weight: 0.1 lb (Yes : .098 lb) - Minimum wall thickness:...

... integrity and manufacturability. ...For this entry, the mass was reduced by 5 grams (0.01lb), volume by ~3cm^3, while the overall geometry was simplified.Mass: 0,033kg/0.07lbVolume: 24,18cm^3/1,48in^3Manufacturing method: FDMMaterial: Ultem 9085

Ultra lightweight bracket, one-piece design of only 0.028 lbs and a volume of 0.578 cubic inches. Basically two mirrored parts connected to each other through a bridge with an elastic hinge.Using common 3D printing features to reduce mass of...

Set of ultra lightweight brackets of only 0.021 lbs and a volume of 0.440 cubic inches (total). Basically two mirrored brackets to be attached to the launch vehicle with 2 bolts each.Using common 3D printing features to reduce mass of unstressed but...

Set of ultra lightweight brackets of only 0.018 lbs and a volume of 0.376 cubic inches together. Total mass can be reduced to 0.016 lbs but that would result in an unstable part to 3D print and a violation of the edge distance requirements.Using...

These are for attacking to you bowl or plates for adding Dip or Sauce ;) *Safe 3D printing materials for food contact (FDA approved)* Ceramics PLA without additives PET, PETG / T-Glass ULTEM 9085 Polypropylene Natural grade Nylon 6 & 6.6 (without...

These are for attacking to you bowl or plates for adding Dip or Sauce ;) Safe 3D printing materials for food contact (FDA approved) Ceramics PLA without additives PET, PETG / T-Glass ULTEM 9085 Polypropylene Natural grade Nylon 6 & 6.6 (without...

Engineers use Stratasys systems to model complex geometries in a wide range of thermoplastic materials, including: ABS, polyphenylsulfone (PPSF), polycarbonate (PC) and ULTEM 9085 and Nylon 12. Stratasys manufactures in-office prototyping and...

Engineers use Stratasys systems to model complex geometries in a wide range of thermoplastic materials, including: ABS, polyphenylsulfone (PPSF), polycarbonate (PC) and ULTEM 9085 and Nylon 12. Stratasys manufactures in-office prototyping and direct...

(Project)File: bracket Atlas V Centaur launch vehicle V1.ipt; iges; step.(Physical)Material: Ultem 9085 Density; 0,04 lbmass/in^3 Mass: 0,694568 lbmass Area: 90,8013 in^2 Volume: 17,3642 in^3 (Materials)General Mass Density: 0,04 lbmass/in^3 Yield...