ultimaker 2 feeder upgrade 3d models

i made this grooved Ring for the new feeder upgrade from Ultimaker. Replaces the delrin ring. Test at your own Risk.Instructions100% infill. needs to be tight fit. you may have to adjust this to your Printer tolerances. ...i would like to make the outer...

i made this grooved Ring for the new feeder upgrade from Ultimaker. Replaces the delrin ring. Test at your own Risk. Instructions 100% infill. needs to be tight fit. you may have to adjust this to...

This is a fully printable feeder upgrade for the Ultimaker. It improves by far the feed of the filament by reducing a the friction generated by the stock parts. Instructions Just print it and ad a...

This is a fully printable upgrade of all 3 parts of the assembly, whilst keeping faithful to the Ultimaker original, using the outer shape taken from the lasercut drawings published. You will need a 6mm ID, 10mm OD, 3mm wide bearing, this cost me...

Instructions once printed take your old feeder apart and use a standard nut (not one with a lock thread) plop the bearing on and away you should go. ITs a little tight getting it in there but it works nice. BTW make sure you print it with 100%...

Instructionsonce printed take your old feeder apart and use a standard nut (not one with a lock thread) plop the bearing on and away you should go. ITs a little tight getting it in there but it works nice. BTW make sure you print it with 100% fill..

Works with the Ultimaker Original and the Ultimaker Original +. I was not very happy with the existing designs as their teeth profiles didn't match the motor gear or they were non-symmetrical or it wasn't possible to fasten the stepper screws with...

... Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Yes Supports: No Resolution: 0.1 mm Infill: 100% Notes: PLA is not strong enough. For me I used Colorfabb XT with excellent results. I did not try ABS but I think it will be ok.

The motor shaft of most of the steppers is too short as to use it inside the UM2 to connect the Feeder. ... Therefore i made this 90° angled holder for the Titan to use the existing holes.

The motor shaft of most of the steppers is too short as to use it inside the UM2 to connect the Feeder. Therefore i made this 90° angled holder for the Titan to use the existing holes. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts:...

:D Some Baseplates to upgrade your Ultimaker 2 (the original should also work, since its a similar case) with some cool bricks or minifigures that can observe your printing progress. The plates go onto the top frame and should be secured with...

This part will help guiding the filament to the feeder. ...The spool can be mounted lower than standard position and this tool provides a better angle for the filament to the feeder.

With an Ultimaker 2 feeder, you have to adjust the e-step parameter from the ulticontroller in the "motion" menu'. My new e-step parameter with MK8 drive gear is 157 (default is 836). ...The e-step depends of your own driver gear used, I suggest to...

Ultimaker 2+ Fan Shroud Upgrade

This feeder designs combines the two existing feeder designs from |Robert| and Geeks:- https://www.youmagine.com/designs/alternative-um2-feeder-version-two- https://www.youmagine.com/designs/extruder-um2-version-2- Body and latch by |Robert|-...

You could skip drilling the holes for the two uppermost screws, but I'd strongly recommend you to drill because that extra contact point improves the reliability quite a bit.I've also included the flipped body and cover, which is what you see in the...

Extruder für Ultimaker 2(+) / 3 2.85mm Materialdurchmesser Es wird ein Zahnriemen 2GT-110 in der Breite 6mm verwendet. Die Schrittanzahl für einen 200 step/rev Motor ist bei 660 step/mm in die Firmware einzutragen. Die Antriebszahnräder gibt es zum...

It rotates the feeder so that the knurled side of the filament does not rub against the bowden tubes side. Please not that you filament reel cannot be bigger than your typical 1KG reel. The new position of the feeder stepper blocks a part of the...

This feeder spacer frame is needed if you want to fit the Chinese Ultimaker 2+ feeder to the Ultimaker 2, as the stepper shaft is too long on some Ultimaker 2's, so instead of cutting the shaft, which I think is a bad idea, you can use this spacer. ...

Full wiki guidelines here: http://e3d.online/E3DmyUltimaker Or get the full kit here http://e3d-online.com/Ultimaker-Extrusion-Upgrade-Kit This E3D conversion is optimised for: Ultimaker 2, Ultimaker 2+, Ultimaker 2 Extended Ultimaker 2 Extended+ The...

See original design by dmols herehttps://www.youmagine.com/designs/ninjaflex-geared-ultimaker-2-feeder

Kit for mount e3d v6 or similar hotend on Ultimaker 2/2+ family. ... In a few days the installation manual with complete instructions

Ein neuer Förderer/Feeder für Ultimaker 2. Andere funktionieren auch, aber man kann die schlecht Nachstellen über die kleine Schraube. ...Auch war dort die Schlauchhalterung immer problematisch.

if you want to get the designfiles of this feeder you can download them here;https://www.youmagine.com/designs/feeder-for-ultimaker-2-rail-system ultimaker2 rail system ;http://www.thingiverse.com/thing:430899 my original feeder...

Part #9 of the Ultimaker 2 Extrusion upgrade kit here: https://ultimaker.com/en/resources/19641-installing-the-extrusion-upgrade-kit The two end holes don't line up perfectly because I couldn't find the drawings... but it was close enough for me.

In combination with changing my Ultimaker 2 extended to use 1.75 mm filament I added this feature so it would successfully print flexible filament (TPU). The original setup from Ultimaker presented too much Bowden tube with a curve and this would...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

External UM2 feeder with holder for the Ultimaker 2 case. They mount ontop of the UM2 and reduces the lenght of the bowden tube around 30% which might make it easyer to print flexible materials. ... To mount it you have to replace the existing case...

External UM2 feeder with holder for the Ultimaker 2 case. ...They mount ontop of the UM2 and reduces the lenght of the bowden tube around 30% which might make it easyer to print flexible materials.</p> <p>To mount it you have to replace the existing...

This an original part of the Ultimaker 2+ Extended filament Feeder that I broke accidentaly. The model has the exact mesurements but I had to print it at 110% scale in ABS 255°C with the board at 90°C. This thing was made with Tinkercad. ...Edit it...