ultimaker 2 filament guide for 90 degree rotated spool 3d models

Guiding the filament from the spool requires careful manipulation to ensure it reaches the next guide without tangling or snagging.

... chin from hitting the front left black frame during printing. Print with raft and support, using standard settings at 10%, 2 shells, 0.20 mm. This design was created on Tinkercad.com; search "Bre Pettis Filament Guide for Replicator 2" to find it.

To ensure a proper fit, screw the M3 screw straight into the bearing as possible, using it as a guide. Once installed, mount the coil holder according to standard procedure, measuring approximately 50 mm (as shown in Picture_04). If needed, refer to...

This filament guide inserts into the original spool holder without altering its design. Installation is effortless, requiring no drilling or screwing. To minimize friction in the filament opening, simply sand it down. You have two options: a loose...

Filament spool guide for the Ender 3 Max and Pro use some extra bowden tube through the hole and hot glue it using the cut outs. ...allows for nice even spool feed out while not worrying about the filament getting wrapped around the holder.

My DIY Spinning Holder for UM2 Pro, designed for hassle-free printing without unnecessary supports.

Filament roll holders guide filaments into their correct places to prevent snags on axles when utilizing full filament rolls. The filament sometimes escapes from its roll and hooks onto the axle. This holder stabilizes both the filament spool and the...

This is a hinge designed specifically to function with a 70-degree stop for use within Printedsolid's Ultimaker 2+ Extended Safety Enclosure.

Orca 0.2's spool holder or filament guide requires printing the following STL files for assembly: 1x orca\_top\_spool\_mount\_printbed.stl, 1x orca\_top\_spool\_mount.stl, and 2x orca\_top\_spool\_mount2.stl. Assemble with three 8mm threaded rods,...

......I made this for my Ultimaker 2+ Connect but I think it will also work on the dual spool version of the Ultimaker 3--you'll just need to flip it over for the spool that goes to the left. ...Nothing special to print--I used white to match the printer.

After remounting the filament spool holder on the back of our machine we noticed the filament sometimes was "jumping off" the spool. ...For now we mounted it with double sided tape, I made two holes for small selftapping screw though.

After remounting the filament spool holder on the back of our machine we noticed the filament sometimes was "jumping off" the spool. ...For now we mounted it with double sided tape, I made two holes for small selftapping screw though.

A little circle for a filament spool. With this tool, your filament spool will roll smooth. It is made for the original Filament-Holder of the Ender-3-Pro, but it fits for other printers too. ...You can download the f3d file and customize it for your...

... holder including filament guide. You still need: - 4 wood screws for the supports and filament guide (Ø4mm) - 2 bearings 625ZZ (Ø16mm x 5mm) - 2 screws M5x25 + nuts Have fun with it ;-) You are welcome to follow me on Instagram: @ 3ddruckbude

This text is about a modified size holder designed for wider filament reels, featuring holes larger than 30mm and standard length. Suitable for reels with smaller holes like those from JET. ...Printed with light supports, the holder may need some effort...

The spool originates from Woofy's ingenious design on YouMagine, specifically the Spool Holder for Loose Filament. An alternative hub option comes courtesy of didierkl, also found on YouMagine, under Alternative Hub for Loose Filament Spool.

I crafted a custom pulley system for the Ultimaker 2 that greatly reduces tension on the filament spool. The pulley wheels are engineered to work seamlessly with regular skateboard bearings. To fine-tune the spool frame wheel, simply remove the knob...

Arm is longer to acomodate for spools with larger diameter. ...Goes well with my remix Spool Holder for Large 2kg Spools.

I made this addon for the 2kg spool holder because the filament always jumped off the spool when the print head was too high. It uses 2 M3 nuts, 1 M3x30 screw and 1 M3x10 screw. I also used the short bowden tube from the original filament guide. All...

This is a remix of https://www.thingiverse.com/thing:4683505 with the arm rotated 90 degrees to provide a nice bend for handling filament with a read-mounted spool such as from https://www.thingiverse.com/thing:4333835 The spool holder has its own...

Filament Guide - Out with the Scotch Tape! Print Settings Printer: Geeetech Prusa i3 Supports: No, we've got this one covered. Resolution: We're pushing out a sharp 0.2 resolution every time. ... Infill: We're filling it in at a solid 10%.

This is a remix of an existing 90 degree filament guide, which is an excellent functional design, but it turned out to be fairly cumbersome when changing filaments or calibrating eSteps. ...This simplified versions attempts to overcome those issues,...

MyMiniFactory's precision-designed spool holder for the Ultimaker 2 3D printer prints seamlessly without any support, making it instantly functional and ready to use right out of the box.

This clip-on filament tube guide is specifically designed for the Makerbot Replicator 2, but it may also fit other printers. I used it to relocate my filament spool to the front of the printer by using a bolt-on spool holder from...

Spool Holder for Ultimaker Printers. To build it, you will need: - An eight-millimeter diameter threaded rod that is one hundred fifty millimeters long - this length accommodates M8 nuts. ...- Three M8 nuts - Two 608zz bearings - Two BearingHolder_PaL...

There's separate left and right versions depending on what side you have your filament spool on.EDIT: I had the model names backwards, whoops.

The Filament Guide is a crucial component of 3D printing technology, responsible for regulating the flow of melted plastic material as it cools and solidifies into the desired shape. Its primary function is to maintain a consistent temperature,...

Original Ultimaker spools feature a unique clip design that provides secure and easy filament loading. ... Note: The Flesch-Kincaid grade level of this rewritten text is 9th grade.

Print with regular settings at a 0.2mm layer height, three walls.\r\n\r\nWhen using an Ultimaker printer such as the S5, it's recommended to take out the filament guide from the spool holder; otherwise, the clip will collide with the guide and stop...

For this reason I created the little Filament guide that prevents that the filament can jump of the pulley while the Z Axis or spool is moving. A 3cm PTFE Tube is needed and the bore should be drilled that the PTFE Tube fits snuggly. ... Fusion 360 f3d...