ultimaker 2 upgrade to 3 3d models

... 3 printers with the existing spool holder. This is an offset spool mount to make it easier to use large spools Note that if you're using the Ultimaker 3, it will block access to one extruder, but still handy overall. ... Category: 3D Printer Parts

... 2 and 3 printers using the existing spool holder. This is a lateral spool mount designed to make it easier to use large reels. Note that if you're operating an Ultimaker 3, it will block access to one extruder, but still proves handy overall.

To create a DIY printer modification, start by acquiring a 32x32 cm plate with a thickness of 2-3 mm made from acrylic glass. Place the necessary components onto the plate and drill holes in it for mounting purposes. When using "DoorHolder2" pieces,...

This upgrade links the original Ultimaker 2+/3 extruder to a Bowden tube on the filament insertion end. The printed component swaps out the top cover of the standard extruder. ...You'll also require an additional Bowden coupler for installation.

You might want/need to print the small gear as well, so that's included but it's a straight copy of the original from the ultimaker github https://github.com/Ultimaker/Ultimaker3/blob/master/1969/1969-G/1969-G.STEP which is licensed under...

This component serves as a supplementary attachment specifically designed for the original Ultimaker 2+/3 extruder, allowing it to connect seamlessly with the bowden tube at the filament insertion point. The printed part completely replaces the top...

Upgrade your Ultimaker's feeder with this 3D printable part, which significantly reduces friction caused by stock components. Easy to assemble and install; simply replace the original part with the provided roller (10x6x3) for enhanced filament feed....

Printed using high temp material on form 2 and use on ultimaker 2, 2+, 2+ extended. ...Works with Ollsen block and gives great results.

The upgrade includes printable modifications to all three components while maintaining fidelity to the original Ultimaker design. To implement this, you'll need a 6mm ID, 10mm OD, 3mm wide bearing, available for £1.99 on eBay. This modification...

Modified version of Pagoda-2 soldering antenna assembly instructions, sourced from the original article found at www.maartenbaert.be/quadcopters/antennas/pagoda-antenna.

This item serves as a vital accessory for the authentic Ultimaker 2+/3 extruder, enabling seamless connection to the bowden tube directly at the filament insert point. By installing this printed component, you effectively swap out the top cover of...

I designed an enclosure for my Ultimaker Original printer to minimize temperature fluctuations. The individual window components are precision-cut from 3mm acrylic using a laser cutter, with each piece overlapping by 5mm. A total of eight corner...

... soldering it to the other pin. Proceed with soldering the components to the electronics (LED A to +5V, LED K and photo transistor E to GND, and photo transistor C to input). ...Lastly, modify the firmware by changing Z_ENDSTOPS_INVERTING to false.

To measure the spring accurately, follow the high or simplified measurement procedures outlined in http://www.vinland.com/Spring-Testing.html. Note that the spring for the upgrade is not critical, with a vast adjustment range. Additionally,...

... ensure proper tightening. Print the modified model with 100% fill for optimal strength. To check movement during printing, add black dots on the outer side of the bearing using a sharpie and use a flashlight for better visibility through the gap.

This component leverages clamping an M4-bolt over an extended length (±10mm) as opposed to ±3mm, thereby preventing platform shifts during printing. Three identical blocks are used, with two positioned closely near the Z-stage and spaced apart for...

Make sure to print it with 100% fill; anything less will crumble under pressure as needed to push the bearing against the filament. I added small black dots to the outside of the bearing with a sharpie - about 15-20 of them. The reason is so through...

Replacement Lever for Ultimaker 2+ and 3 Feeder Includes Fusion 360 Model. A metal rod goes through the center of the bearing, measuring 3mm in diameter and 11mm long. This is because the 3D printed part was not strong enough on its own (it snapped...

This configuration is necessary due to the Ultimakers' tendency towards back heaviness and the Sorbothane half-spheres' requirement for adequate loading to function optimally. ... These feet perform exceptionally well compared to other solutions I've...

I modified it for better printability and resistence, so you can upgrade the older edition of kp3s to the 3.0, just printing this in ABS or ASA, and ofc you can use the mods for the new 3.0 edition. The weight is near the same of the original. I used...

I Utilized a 5/16" bolt, 2 skate bearings from a spinner project I had left over and an acorn nut as we call them here in the US to round out the design, then attached it to ZAxis3D's adapter. It works great, super smooth. ... I am currently working on...

... technology. ...The durable duct support is precision-printed with high-strength PLA or advanced materials, ideally CNC-milled from lightweight carbon fiber for maximum performance (check out the Intrepid V2 3-Inch Cinewhoop Upgrade on AirbladeUAV.com).

... to verify that everything is functioning correctly. ...Then, allow it to continue printing overnight and resume testing in the morning with the finalized model, ensuring that any software updates have been successfully downloaded and integrated.

--- Instructions Build Materials: Stuff to buy: * 2 x laser pointers (cheap, small ones) $8 * 6 x LR44 batteries $3 (pack of 10) * 6 x LR44 battery holders $4 * Stuff I already had: + Soldering iron and solder + Wire + Hot glue gun and glue + Pliers...

If your WSKEN always disconnecting. ... Uprade from V1 to V2

This adapter is to convert the Ultimaker standard bed mounting with 4 alignment screws to 3 alignment screws, allowing for easier 3-point alignment. Add this adapter and drill a 3mm hole in the middle of the two back mounting holes for the ultimaker...

This adapter simplifies the Ultimaker standard bed mounting by converting it to 3 alignment screws for easier 3-point alignment. To install, drill a 3mm hole in the back holes and add a spring. After adding the adapter, level the print bed from the...

I used and adjusted some designs, so first I want to give credit to: T70E: https://www.thingiverse.com/thing:2615653 I used his hinge for the Ultimaker 3 door. Thank you! littlebignita: https://www.thingiverse.com/thing:1241911 I used his S6Edge...

I used and adjusted some designs, so first I want to give credit to: T70E: https://www.thingiverse.com/thing:2615653 I used his hinge for the Ultimaker 3 door. Thank you! littlebignita: https://www.thingiverse.com/thing:1241911 I used his S6Edge...