ultimaker 3 dual extruder 3d models
830031 3d models found related to ultimaker 3 dual extruder.youmagine
I disliked the wobbly design of the Ultimaker Original spool holder and created a fitting spool bar inclusive lock for dual extrusion to keep filament spools working smooth. Just remove the small parts of the spool holder and replace them with the...
youmagine
It alters extruder lever with new one, that lets You lock it in open position. Simply press lever down to lock it or pull it up to releas it back!. No more pain in your finger, just lock the lever and use both hands to whatever You need. It has also...
thingiverse
I upgraded my Ender 3 with the dual extruder kit from TH3D. But I couldnt find a good adaptor to mount the extruders. ...So i designed this in fusion 360.
thingiverse
I was able to print dual color prints with no ooze shield and no purge block!!! Detailed setup documentation and assembly instructions will be put up soon. *Ender 5 plate has not been tested. If you need adjustments, please let me know and I...
thingiverse
Dual filament spool holder for Ultimaker 3 extended that holds spools separated. This is inspired from https://www.thingiverse.com/thing:2884359 but I wanted something more strong (specially for the top one) and be able to adapt any roll holder so...
thingiverse
Cable Clip for the Ultimaker 3. ...Tested in PETG, should work with other materials too though.
cults3d
This item is an add-on for the original Ultimaker 2+/3 extruder to connect to bowden tube at the filament insert side. The printed part replaces the top cover of the original extruder. ...You will need an extra set of bowden coupler.
thingiverse
This item is an add-on for the original Ultimaker 2+/3 extruder to connect to bowden tube at the filament insert side. The printed part replaces the top cover of the original extruder. ... You will need an extra set of bowden coupler.
youmagine
This item is an add-on for the original Ultimaker 2+/3 extruder to connect to bowden tube at the filament insert side. The printed part replaces the top cover of the original extruder. ...You will need an extra set of bowden coupler.
thingiverse
... for the lame object - I just started to learn Fusion 360 what I used to model the carriage. I just printed it out but did not test at all. https://www.youmagine.com/designs/ultimaker-minimum-printhead-with-threaded-bowden-lock-dual-extruder-version
thingiverse
A support for 2 full métal geared extruder with a top fan, on ultimaker 2. ... Link for the extruder (AliExpress) :...
thingiverse
This is a second quiet retraction extruder mount for the Ultimaker 1. It is inspired by http://www.thingiverse.com/thing:53690. The idea is absorb the motor vibrations so that the Ultimaker case does not act as a rosonance body. It is planned to...
thingiverse
Amazon links : Ender 3 MK8 Extruder Drive Feed Dual Gear t.ly/V_wz t.ly/WuYx
thingiverse
I upgraded me ender 3 with the TH3D dual extruder board https://www.th3dstudio.com/product/creality-cr-10-and-cr-10s-dual-extruder-upgrade-board/ I got the 2 into 1 hotend from ebay...
thingiverse
Kann man Rechts an die Wand schrauben mit M8 Schrauben. Ich habe dank der Motorkühlung keinen Platz mehr hinterm Drucker. ...Stützstruktur ist ratsam.
thingiverse
To the set of nozzles spacing in Cura Prefs. Default is 21.6 my 22 :) Why ??? ... wrong distance and share link is bad or the color layers are offset see the one bag clip Whale is broken and now is stick announced In German-> Deutsch falscher...
thingiverse
I remixed the build by zrxmopar to basically not have both extruders handing, but only one. The motor 0 stays where it was in the vanilla ender 3 (pro). I think I used both blender and finish it with fusion 360. I'm uploading the .stl and the...
thingiverse
My Ultimaker 2+ started jamming a ton and I discovered that the extruder lever had warped at the bearing mounting point causing it to bind. Using the UM open source files I modded the lever arm to assemble with screws - making everything much...
youmagine
My Ultimaker 2+ started jamming a ton and I discovered that the extruder lever had warped at the bearing mounting point causing it to bind. Using the UM open source files I modded the lever arm to assemble with screws - making everything much...
thingiverse
Make layer time like 20 seconds, adjust the part with breakaway knife and 3mm drill bit. ...Put inside the feeder 1 or 2, done. You can now print flex with less jamtastic experience. Hey Ultimaker, for 3 grand these should be default.
thingiverse
This part uses all the same hardware that is currently used by the Ultimaker 2 so there is nothing else you will need to buy. It is also assembled the same way as the original so its super easy to transfer the parts! ... I have only tested it on a...
thingiverse
This is a work in progress, dual extruder mount for Cube 3
thingiverse
... ... Below is the extruder that works with this One file had a wire mount and one does not https://www.amazon.com/WINSINN-Extruder-Creality-Upgraded-Aluminum/dp/B07SY745CF/ref=sr_1_4?keywords=ender+3+pro+dual+gear+extruder&qid=1570750051&sr=8-4
thingiverse
Inspired from the "CR-10 / Ender 3 Direct Drivinator" from Madau3D Designed to fit with "Dual Gear Mk8 Extruder". ... https://www.aliexpress.com/item/33041468821.html?spm=a2g0s.9042311.0.0.769c4c4deoletK
thingiverse
Ender 3 mit MK8 Dual Direkt Extruder - alle anderen *stl Dateien siehe: https://www.thingiverse.com/thing:4541435 Schritte einstellen: https://teachingtechyt.github.io/calibration.html#esteps...
thingiverse
Not a remix, but designed from the idea in https://www.thingiverse.com/thing:2605108 Guide to run filament straight into the extruder This is on a 3 v2 with dual gear extruder, which I think feeds in higher than the stock; try it if you want. ...
thingiverse
Improved upon my previous design to feature compact form factor and better filament inlet, this extruder cover fit tightly on your dual gear extruder to keep the dust out. ... The cover also has the right cutout for this cable chain extruder mount...
thingiverse
This mount is intended for dual extruder Ender 3 Pro setups. While it is designed to allow the use of the original stepper mounting screws, I do suggest getting slightly longer screws as even though it's only 0.5mm thick, it will make them easier...
youmagine
So I finished putting together my Mendel Max 3 dual extruder 3D printer recently, and as usual I have a horrible time leveling the bed. As a result, I go and get a Dial Indicator from Harbor Freight, but unfortunately, there isn't an easy way to...