ultimaker v1 3d models

This is an adaptation of the standard Ultimaker drawings, but with some handy features thrown in. Notes: -All lettering on the parts has been removed for less clutter in the acryllic version -Slider blocks have 1mm more depth to improve tension of...

A holder for your Victorinox 14mm thick knife, it will clip on top of your Ultimaker V1 3D Printer. it might need to be scale down just a little it has i bit to much play. ... Instructions I made mine...

The original hot end on this Ultimaker Failed and I had a Pico Hotend that I wanted to try so i came up with this mount.

Ein neuer Förderer/Feeder für Ultimaker 2. Andere funktionieren auch, aber man kann die schlecht Nachstellen über die kleine Schraube. ...Auch war dort die Schlauchhalterung immer problematisch.

Halterungen für die Glasscheibe beim Ultimaker 2, damit man die Metallklammern weglassen kann. Bitte auf die Position beim Einbau achten, damit der Lüfterhalter nicht kollidieren kann. ...Take care of the position.

Ein Kabelschutz für den Ultimaker 2. Eine weitere Version mit schwingungsgedämpften Füssen usw. ...ist in Arbeit.

Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: Normal Infill: 20% Notes: Designed taller than you need - feel free to adjust the bottom cutoff before printing. ...The print in the photo has a 15mm...

ZAV-U 40mm Turbo Kit v1 ultimaker

ZAV-U 40mm Turbo Kit v1 ultimaker

After receive my ultimaker 2 i found standart cooling fans not enought for cooling, and design little update.This design is for fast and easy to remove There is mount for 120mm fans. ...With this upgrade quality of print improved and stepper motors X,Y...

A fan duct for the Ultimaker 2 by PeltonEngineering! Uses the fans airflow far better then the original one. I tried to optimize the cooling as much as possible. Also you need no screws for it. IMPORTANT: You have to print the Y-Axis switch...

UPDATE V1.1: I created a little improved version. I change the hole where the bowden tube fix will be inserted, before it was a bit hard to fix the clamp. ... Also I thickened the section on the outer body where the cables will be fixed because on...

UPDATE V1.1: I created a little improved version. I change the hole where the bowden tube fix will be inserted, before it was a bit hard to fix the clamp. Also I thickened the section on the outer body where the cables will be fixed because on my ABS...

UnitedPro B3510X05B Fanduct with cablemanagement for the E3Dv6-Ultimaker printhead. 1 screw is sufficient for clamping the fan :-) so its weight optimized ! Have Fun ! ...

v1.1 enjoys a better spindle end stop, chamfered spindle cuff offset, and a small rail on the mount's upper tab to improve leveling.v1.2 boasts a slightly longer spindle, improving spool compatibility (thanks to gbo for the suggestion!) I didn't cut...

finish the second test print,without suppourt,just to check if everything its correct then let it printing till tomorrow for final model,better to wait a bit to download.

Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options:...

A fan duct for the Ultimaker 2 by PeltonEngineering!Uses the fans airflow far better then the original one. I tried to optimize the cooling as much as possible. Also you need no screws for it.</p><p>IMPORTANT: You have to print the Y-Axis switch...

Inner diameter of 0.24 mm are drawn largerBall bearings must be pressed fitWhen installing make sure that you so screw the M3 screw straight as possible. I have the ball bearing used as a guide. When finished Mounted then press coil holder purely in...

Revision Notes 5th November 2013 Added Three newer versions 1.2A 1.2B 1.2C and 1.2D identical to previous version, but includes a gopro name plate on the fronts. 4th November 2013 added two newer versions 1.2 and 1.2a for hero 3 revised to have...

Revision Notes 5th November 2013 added Three newer versions 1.2A 1.2B 1.2C and 1.2D identical to previous version, but includes a gopro name plate on the fronts 4th November 2013 added two newer versions 1.1 and 1.1a revised to have thinner walls-...

Case to fit an Ultimaker v1.5.7 PCB (other version might fit as well) and the attached Adruino. ... Space for 2 40mm fan to cool electronics

Ultimaker OSHW project (ultimaker.com)

In addition, over the course of the months after it starts shipping, the Ultimaker 2 files will be released.The electronics have been released here:http://reprap.org/wiki/Ultimaker%27s_v1.5.7_PCBAssembly instructions can be found...

Older versions of the electronics were published on the RepRap wiki: http://www.reprap.org/wiki/Ultimaker%27s_v1.5.4_PCB http://www.reprap.org/wiki/Ultimaker%27s_v1.5.3_PCB http://www.reprap.org/wiki/Ultimaker%27s_v1.3_PCB...

This thing has moved to Youmagine: https://www.youmagine.com/designs/ultimaker-bowden-pop-stop This little gadget is for the Ultimaker v1 Hot End and does these things for you: Is a printable solution to bowden slipping/popping problems Solves the...

This little gadget is for the Ultimaker v1 Hot End and does these things for you:  - Is a printable solution to bowden slipping/popping problems  - Solves the filament plugging in the hot end problem  - Reduces the stress on any clamping solution (so...

that wasn't matching with the names for the pins on EXP2 on the Ultimaker board: http://www.reprap.org/wiki/Ultimaker%27s_v1.5.3_PCB Looking on the other side of the Micro SD board that has "WAVESHARE" shows labels to the pins closely matching to the...

Ultimaker-frisbees