under desk drawer add on 3d models

This was designed to work with Drawer Organizer SKU: 219294 but will likely work for other things. Designed to use size 10 x 5/8 wood screw. Smaller flush screws may work. No supports necessary. ... If using the organizer intended then holes...

This heaphone hook is engineered to fit snugly onto 32mm square tubing, commonly used in the IKEA Gallant desk system. ...To accommodate larger tube diameters, simply scale up the design by dividing your desired size by 32.

This is a desk mount designed to hold a headphone hook in place, secured by screwing it into the underside of your workspace. ...The mounting system is specifically engineered for use with #6 wood screws.

A simple yet effective solution for organizing cords and accessories - a sturdy clip that attaches to the underside of a desk, keeping my Sony MDRs secure and within easy reach while they're charging.

... ...It is easy to mount and with the swivel function cables/power strips/... can be placed comfortable in the cable channel.For my desk I used:3x CableManagement_P16x CableManagement_P26x CableManagement_P31x Frame profile 2000 x 100 x 40 mm (e.g.

Simple headphone holder designed to be screwed under the table using two M3 / M4 screws. ... No supports needed.

Under-floor storage units are designed to maximize space by utilizing double-sided adhesive tape to secure them in place.

*** what you need: *** - 8x M8 threaded rods (in my case 31 cm long) - 32x M8 Normal-Nuts - 2x M8 Hut-Nuts - 34 M8 washers - 4x M8x40 Screws with a flat hat (the hat is facing to the synth as you see on one of the pictures) - 12x Screws for mounting...

Update 1/5/2016: I experienced issues with these staying attached to my desk, so I added a hole allowing them to be secured with screws. Update 2/5/2016: This design didn't meet my expectations, so I completely re-designed it. ...The updated version...

Supports: No problem at all Resolution: 0.2 millimeters, precision guaranteed Infill: 20% should do the trick, but feel free to experiment with anything you like Notes: I designed this holder to be super easy to install using velcro strips, but if...

... your workspace. ... Printing is a breeze, taking approximately 50 minutes with just 0.4 layers, making it an efficient process. With only two screws required, this holder lets your desk do the heavy lifting, ensuring a smooth installation experience.

I designed this holder specifically to attach my case backpack to the underside of my desk. It's also likely to work perfectly for holding headphones in place. I sliced the design using Cura's adaptive layering feature, which results in a...

This innovative device is specifically engineered to securely fasten underneath a standard office desk, providing a convenient storage solution for your favorite listening gear. ...By keeping your headphones neatly positioned, you can enjoy...

... a trash can for my office that wouldn't be used by everyone else, so I came up with this solution. ...It fits snugly underneath the desk and glides smoothly in and out for convenient disposal. ...My goal is to share its usefulness with others as well.

Modeled a simple bin that can be mounted underneath a desk. Designed to fit a pedal bin liner (perimeter of 96cm). Can be glued together and rails greased. ...The sliding action frees up over time or with some light sanding.Requires:Rail Section x4Rail...

Mounting brackets for a 4U rack, designed to be installed underneath a desk. For heavy loads, print the rear supports to provide additional weight-bearing capacity. ... **Required Hardware:** 16 Pan Head Screws (M6-1.00 x 25mm) 16 Hex Nuts (M6) 4...

Mounting an Intel NUC beneath a desk requires a swift installation. The assembly utilizes six screws. ...Crafted with precision, this design allows the device's feet to remain intact while being compressed slightly, resulting in a tight, stable fit that...

Basic Headphone stand that clamps to desk leg. The Leg of my table is 40.5mm wide, and my headphones are 36mm wide. ...Print Settings Printer Brand: Creality Printer: Ender 3 Supports: No Resolution: 0.16mm Infill: 25 Filament: Hatcbox PLA White ...

It uses two small screws (thread outer diameter <4 mm, screwhead <6.3 mm) to attach to the underside of a desk. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 mm layer height How I Designed This This...

This is my Headset holder design, i printed it to keep it of my desk. It works great when it is printed in PETG i did not try PLA for now. Printed it with the Bambu Lab P1P in PETG Black. It is hold with 2 screws. I used wood screw, with a...

Remix to add a second hook dedicated to the cable. ... Changing the length for my Triton helmet v2: change the screw hole

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

A simple Headphones holder to be mounted under any spot you need. ... Designed around a ps4 wireless headset but made with plenty of clearance for larger headphones If you find it doesn't fit your headset let me know and I can modify of upload the...

CAD is on onshape -https://cad.onshape.com/documents/2017ce8562f281347a76438e/w/232f719bd0c669142994039e/e/1e904d1be4e9b1ee22595a3f

Original idea was good stuff. I rounded off some corners because my printer likes to fail on corners. Removed parts that glued on, added hooks on the hook part. Separated the hook and top part for easy printing. Used an M6-25mm screw to attach the...

The original file would not fit on my ender 3 so I chopped off the front angle and moved the foot back.

... PLA from eBay as it was the only white PLA I had laying around. ... I used 10% gyroid infill and it feels more than sturdy enough. I also put my logo on the front however the .STL file doesn't have that so you can put whatever you want on the front!

......I wanted to hang this on an electric fireplace that is near my TV and then didn't want it to be boring, so I added the Back 4 Blood logo on the front. Since everyone's headphones can have different tolerances, I created an extension for the “Rests”.

You'll likely want to smooth out all the edges so your headphones' pads don't get caught on any rough spots or lumps. ...Check out the OnShape document at...