unger pole adapter 3d models

 I've made it tight enough in this application that screwing the mount on is tight enough not to require any permanent attachment.For smaller poles you could potentially use some rubber inside but I wouldn't go smaller than about 12mm I think and you...

I created a custom adapter for my Intex vacuum after the swiveling connector that attaches the pole to the head broke. Instead of buying a new assembly, I decided to craft my own replacement part. The original OEM part has very thin walls,...

A quick remix of kamilice22 go pro mount, and my own adapter(https://www.printables.com/model/36039-bunnings-paint-pole-to-gps-thread-for-surveyors )Printed with PETG has been fine for me when connecting straight to the go pro ( no extenders etc).

 They have a very good pole mount bracket to attach the AAG CloudWatcher and the optional Anemometer but they do not have a solution to mount the Hydreon RG-9 with them which is the ideal setup.I found a pole mount bracket that looked like it would...

I designed a replacement adapter for my Intex Vacuum when the swiveling pole connector broke. Rather than buying an entire new assembly, I chose to create a custom part that would fit perfectly. The result was a beautifully crafted component. The...

Adapter for mounting the KNX weather station from MDT (model SCN-WS3HW.01) to a pole of roughly 50mm in diameter. The original transparent mounting bracket of the weather station is slid into the adapter and fixed with two screws.Designed for:screws...

The Acurite station used a 3/4" diameter pipe as the pole mount but the WeatherFlow station takes a 1" pole. ... Rather than build a new pole or add a pipe reducer and another stub of pipe, I printed this sleeve which fits over the existing 3/4" pipe.

The design for this pole-adapter sprayer would match my existing roof rake and its accompanying spray can cap perfectly. It's great that the type of spray cans used here have a simple nozzle trigger - no complicated system is required to work them...

I had bought a bird silo and wanted to mount it on top of a pole that was already in the garden. The pole had a diameter of 32 mm. Simply slide into the post and place the bird silo on top. It is custom made for this specific bird silo:...

A replacement cap designed to fit in the top of a 31mm (ID) monitor arm pole and take the flexible part of an IKEA Janso work lamp (free-standing desk version).

I needed to hang my trigger receivers on the light pole below my studio strobes. The receivers I use are Yonguo and have a hotshoe. This allowed for me to hang them under the light. ...I would use a semi-flexible filament, as PLA may crack.

They're using a pole from Amazon at https://www.amazon.com/FeiyuTech-Handheld-Adjustable-Extension-Stabilizer/dp/B074W4NWSR - no idea yet if the model is working correctly, but it probably should be. ...Give it a try if you've got some time.

I decided to install my trigger receivers on the light pole beneath my studio strobes. My trusty Yonguo receivers feature a hotshoe that enables me to secure them firmly underneath the lights. ...To ensure their stability, I opted for a semi-flexible...

Customized version of https://www.thingiverse.com/thing:2089058 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2089058

Simple prints to attach my Sennheiser SKP100 to a boom pole with Rode NTG4+ are within reach. Two STL files are available: Screw = tight 3/8 hole for screw-in installation Loose = loose 3/8 hole The XLR hole is specifically designed for this...

This attachment was created by the SPU Engineering team to hold a ski pole, though other uses are more than welcome! Designed to be easily 3D printed, flexible filament is recommended for optimal results, but you can also use standard hard filament...

This is a precise Polar Finder Illuminator Adapter, specifically designed for use with the Skywatcher Star Adventurer system. To secure the adapter properly, simply insert it and then twist it clockwise until snugly in place. ...Upon completion,...

... under its own weight. There is a small window near the overhang that I used to clear out the snow before making this adapter, but unfortunately it was too far away for me to reach with a shovel and I could only clear half of the snow off the edge.

... where the latch goes so that battery can be inserted without pressing the release. I used the 5Ah Dewalt 20V Max battery coupled with a CC CV UV (undervoltage protected) step-up adapter to power an electric scooter, converting it from lead-acid.

English : I made an adapter for Xiaomi Mi Computer Monitor Light Bar for this mount : https://www.thingiverse.com/thing:4976305 Français : J'ai créé un adaptateur pour Xiaomi Mi Computer Monitor Light Bar en utilisant ce montage :...

A simple adapter to work with the below cherry pickers. Using zip ties, such as these [zip ties on...

Adapter um normale Schrubber/Besen an Poolstangen zu verwenden. ... --------------------------------------------------------------------------------------------- Adapter to use normal scrubbers/brooms on pool poles.

Pole

Key details include: * A total of 24,985 points were used to create this digital masterpiece * The intricate design consists of 23,537 polygons that bring the hoverboard to life * With a total of 32 objects making up this stunning model, it's clear...

This is a pole, which could be used for the lamp base's pole

It's an adapter for Mikrotig wAP LTE to mount on pole. ...Two different diameters of pole.

Customized version of http://www.thingiverse.com/thing:865533 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=865533

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2WQvrutr13Z

Designed to fit a 28.5mm dowel with 3 screws to attach it to the dowel. I added a hole from the top of the thread so you can screw through the thread into the end of the dowel giving it extra strength. May or may not be needed. Recommend not using...