universal gps car mount 3d models
484513 3d models found related to universal gps car mount.thingiverse
This is a GPS mount that snaps into the top of the QAV250 Frame as a mount point for GPS hardware. ...Clean and simple connection point.
thingiverse
This is a garmin GPS mount. There is a void underneath where you can put double sided tape to secure it to your dash board. Print in PETG or ABS so it can handle heat inside your car. ... Note: I've added a new, stronger version
thingiverse
GPS Mount for S500 quadcopter Printed with PLA (25% infill) support required
grabcad
a combined pixhawk and GPS mount for drones which can be 3D printed and used
cults3d
simple mount for any gps holder. ...need m4 nut and screw and one longer m3
thingiverse
GPS mount for the brush5.5 frame https://armattanproductions.com/pages/kit_detail/2884
thingiverse
antenna and GPS mount i designed to fit on my DC7 , I printed in TPU .
thingiverse
simple mount for any gps holder. ...need m4 nut and screw and one longer m3
thingiverse
3.5g remix of pathfinderzero 's GPS Lipo Mount for BN-220 Module Also fits iFlight GPS module with UBX-M8030K
thingiverse
GPS mount for the top plate of a trot 650 drone. ...Use washers to secure, will fit into the circular indent on a standard neo7/8 gps.
thingiverse
This is a simple GPS mount that screws on the top plate of a ZMR 450 frame, the GPS is held to the plate with a 3M adhesive pad that is usually supplied with the GPS module.
thingiverse
I have yet to complete the final part - the mount to the car. I plan to do this tomorrow. This is an entirely original item, not based on anything else. For avoidance of doubt, this item is licensed under a Creative Commons...
thingiverse
gps mount for the armattan chameleon ti lr 7" quad frame to mount a beitian bn-880 gps module using longer screws on the rear of the top plate it has a hole for the wire and plug to go into the gps after using sticky tape to mount the gps inside the...
thingiverse
GEPRC CineLog35 GPS mount. GPS module is used Bainianxing-BU1025TF with UBX-M10050-KB + Flash Memory, supports GPS, Glonass, Galileo, BeiDou at same time. [GPS module buy here](https://www.aliexpress.com/item/1005004745320234.html) If you would like...
thingiverse
... Venture FPV Quad. ...The "mini gps mount" was designed for a 28mm module. The normal "gps mount" has an integrated 4mm mounting rod. ... Both versions fit into the hood of the quanum venture, as displayed on cover photo - glue/screws are not required.
thingiverse
HGLRC GPS Strap Mount. The holes on the sides are for zipties to secure the connector cable from being tugged. ...
thingiverse
30 Degree mount for 28mm square gps module. Easy to secure with battery strap. ... Print on side.
thingiverse
Designed to mount a GPS module to the AlligatorFPV Frames. ... Check out the complete build:https://rotorbuilds.com/build/26780
thingiverse
Works with: - [RMRC Mini GPS](https://www.readymaderc.com/products/details/rmrc-mini-gps) - [Micro RDQ M8N GPS GLONASS](https://www.racedayquads.com/products/micro-ublox-m8n-gps-glonass) - [Beitian BN-180 GPS...
thingiverse
First, I used the GPS mount design that I had originally designed for the Armattan Tadpole HD GPS mount. Second, I used the anchoring system that Stevensbox designed for the OpenRacer. The mount anchors between the bottom plate and top plate of the...
thingiverse
GPS mount for the GepRC CG3 frame (Cinego 3" drone) with a full DJI Air Unit (no antenna holder for the Air Unit) and Cross Fire. ... The GPS model is BN-220 Print in TPU with supports.
thingiverse
GPS Motorcycle Ram Mount made with black PLA at 75 percent infill. Works perfect for me with a little alterations. Fits 25mm gps ball. ...Created with fusion 360 Step files are also included.
thingiverse
GPS mount that allows to install a GPS module like Beitian BN-880 in the back of AlfaRC Fighter frame http://bit.ly/2EDtbnw . ... Should fit other frames with 20mm spacing between rear stand-offs
thingiverse
18x18 gps mount for the craftedkwads Pegasus variable stance frame. ...Pair it with a module like this:...