universal gps car mount 3d models

18x18 gps mount for the craftedkwads Pegasus variable stance frame. ...Pair it with a module like this:...

GPS mount for the GepRC CG3 frame (Cinego 3" drone) with a full DJI Air Unit (no antenna holder for the Air Unit) and Cross Fire. ...The GPS model is BN-220 Print in TPU with supports.

GPS mount that allows to install a GPS module like Beitian BN-880 in the back of AlfaRC Fighter frame http://bit.ly/2EDtbnw . ... Should fit other frames with 20mm spacing between rear stand-offs

After getting into a car accident over the summer I had no need for my GPS until I got a new car a few weeks ago. Unfortunately, I lost the mount for it that I used to have. A trip to Best Buy later though, and I had a new mount. It was the...

I designed this to mount a BN-880 GPS module to my iFlight Nazgul5 quad. ...The hole spacing is 22mm to fit the rear mounts on my drone.

Early Magellan Roadmate GPS devices used a “T-Slot” socket to mount the device to dashboard, windshield, cup holder and other mount locations. At some point in succeeding models, the “T-Slot” was replaced with a “universal” 16mm ball mount that can...

As there was not nive GPS Platform available for SoxoS Helicopters I just designed my own to mount it directly on a tail clamp which is at the best position for it. So the printed part does not strain on thin parts of the model. Please use PETG as it...

Try the GPS Vent mount for Garmin GPS's today! Instructions Laser cut DXF Files Assemble with M3 screws Vent clips are designed to be inserted horizontally and then turned to be locked in. ... Created...

This is a simple antenna and GPS mount for the ImpulseRC Reverb. ... It is designed to carry this GPS: https://www.banggood.com/7M8M-Ublox-M8N-GPS-Module-for-APM-Pixhawk-CC3D-Naze32-F3-Flight-Control-p-1078657.html?rmmds=search The standoff tolerance is...

... resolution. All feedback is appreciated. Print Settings Printer Brand: Zortrax Printer: Zortrax M200 Rafts: Yes Supports: Yes Resolution: 0.19 Infill: 80% Notes: This GPS Mount is modeled around the Ublox M8n GPS unit, other GPS units may not fit.

This is a mount for the tyro129 drone gps module. ... You can secure it with a zip-tie. First I mounted it on an arm but there it was hit by a prop (this mount protected the gps module from the prop). ...Now it's mounted on the top.

This project is designed to utilise the cup holder mounting points to provide a means of safely holding a GPS or phone to the car. Print, make, and enjoy the experience as directions are available in finger tip distance from the gear stick. First...

This Mount is for a RDQ Source One V3 7" Long Range Frame - 6mm V0.2 DeadCat Arms. ... It fits a Matek MBQ-5883 or similar GPS units.

GPS + Compass Mount for TBS SourceOne V4. Made for Baitian BN-880-Q module. ... Additional slots to optionally fix the RX antennas in a 90° angle.

This is a GPS mount for dronesand this i have used by making the model using 3D print technology PLA as core material.

Simple wall mount for Garmin GPS73. I use it to hold GPS on my boat inside and outside. ... Screen fully visibile even with button reversed.

This was built to screw into your dashboard. ...This was build for a racing car to track times.

Here 3 GPS Mount with no centre hole If printed with a properly calibrated printer this mount will NOT move or wiggle once you tighten the HERE 3 GPS screw.. Use these mounts at your OWN RISK!!!!. ...It is not guaranteed against bird attacks etc...etc ...

... a 14 mm hole in bottom of mount to cool antenna . Antenna power socket at rear to correct global aim to true North. Mount has ability to have GPS with plug forward but OSD heading will be backwards . ...With 20% infill the mount is very light .TPU

This is a simple folding GPS module mount. It requires a short peace if 4mm kite fibreglass which is standard for most GPS modules. Two 15x2.5 mm setscrews are also required to attach the 2 parts and form the hinge. ... I redesigned the original mount...

GPS mounting bracket for Garmin nuvi 50 Attaches to GPS screen and part 2 is the holder that can be affixed to a flat surface (vs the suction-mount that releases in summer heat) Also had a cable clip to keep the wire hidden from view as much as...

... This is the GPS I'm using: https://www.banggood.com/Ublox-NEO-M8N-Flight-Controller-GPS-with-Protective-Shell-for-PIX-PX4-Pixhawk-p-1005394.html The module is easily held in place by simply snapping it on the mount. ... Enjoy, Leo

SPAL ALZ 12V CT universal car window motor

A simple BN880 GPS mount for the Rising Sun FPV Revenant frame. It just replaces the rear cage mount with this. ...Could be more pretty but it gets the job done.

Folding GPS mount to fit on 3 of the arm mounting screws on a F450 quad. ... Just the bottom part, I used some air line for the bit on the end of the 4mm carbon rod.

This is a Mount for sticking the GPS unit on the curvy Fuselage surface outside the plane. The fuselage top is rounder, so the GPS unit cannot stick to it directly. Hence made this part, which can fit to the fuselage nicely using a double sided...

(https://k-edge.com/shop/computer-mounts/garmin-mounts/replacement-garmin-insert-kit/) I placed a few M3x4 threaded inserts in the gps holes but the screws should hold inside the plastic too. ... I have a few ideas to add some features to my design and...

A mount support for dji naza gps, to install the gps + compass module into a drone frame. ...https://github.com/Scicrop/flameweel-parts Print Settings Printer: 3DCloner DH ...

I designed this GPS antenna mount so that I could attach the Adafruit Ultimate GPS V3 external antenna: https://www.adafruit.com/products/960 to a non-magnetic surface (Wood). ...Use M3 bolts For this project, I didn't need 5m of cable, so I designed up...

I added a GPS Mount for the Standart APM 2.6 GPS, fitts perfect on the Top of the Roof Print Settings Printer: Malyan M150 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 20 Notes: Print it Upside down!!