up plus 2 3d models
1217700 3d models found related to up plus 2.thingiverse
This is the modified enclosure from DytHlt for the up plus 2 rear parts cotation has been modified with the help of ecati from sketchup forum to fit the new up plus 2 with level sensor. ... Thx to ecati and DytHtl for this enclosure
thingiverse
From the project of Dyhlt for the up plus one, and the help of ecati from sketchup comunit, here you will find and stl for enclosure for 3d up plus 2 with dimension of rear cover ajusted ! ... That's will be ok now to use this cover panel with rear...
thingiverse
Side mounted 1 Kg spool holder for the Up Plus 2 Printer. ... Slots into the square hole in the Up Plus 2.
thingiverse
First project - a simple cover for the bright LED of the UP Plus 2 that won't stop blinking during printing. The cover is designed to be put over the edge of the printer and has holes so the light is still slightly visible. ... If a Raft is...
thingiverse
The wind barrier, or fan deflector on my UP Plus 2 has never worked very well, as it was intended. There were always substantial air leaks when using the ABS setting for redirecting the air flow away from the part on the bed. I decided to redesign...
thingiverse
CARCASA EXTRUSORA UP PLUS 2 MONKEY CUSTOMS PERSONALIZABLE
thingiverse
This version allows wide spools (3.625") to fit the UP! ...Plus 2. It also fits the regular UP! ...spools which are larger in diameter
thingiverse
This is a larger spool holder for 1 kg spools for the new UP Plus 2 Rotate as per image picture to be able to print
cults3d
pour pouvoir utiliser avec votre imprimante 3D UP plus 2 des bobines de diamètre important ce quide filament à fixer sur votre imprimante à la place du support standard est parfait
thingiverse
Filament Support for Up! ...Plus 2 Printer When I made it I totally forgot about the lateral screws.. so it didn't fit perfectly but I used it like that. ...:)
youmagine
On the Up! ...Plus 2 printer, the fan is exposed, and twice has someone's hand touched the fan, once cutting the finger, and once breaking off a blade. ...This cover snaps over the fan, protecting the fan, and more importantly, the fingers.
thingiverse
Bei meinem Up Plus 2 ist beim Transport im Auto die Stabilisierung der Z-Achse gebrochen. Ein Ersatzteil habe nirgends ich im Netz finden können. Ich habe es also neu konstruiert und schon verbaut, passt und funktioniert super. ... Einfach die...
thingiverse
My original hot end extruder cover was getting worn out after six years of extensive use on my Tiertime Up Plus 2 printer. I looked all over the internet for a suitable replacement or stl file that I wanted, but found nothing that I wanted to use. ...
thingiverse
E3D V6 mount for an Up Plus 2 Print settings I used: -0,1 mm layerheight (I think slightly higher won't be a problem) -60% infill -Printed in PETG but ABS, ASA or another material that is ok with high temps should be fine. Parts needed: -E3D V6 -30...
prusaprinters
E3D V6 mount for an Up Plus 2 Print settings I used: -0,1 mm layerheight (I think slightly higher won't be a problem) -60% infill -Printed in PETG but ABS, ASA or another material that is ok with high temps should be fine. Parts needed: -E3D V6 -30 x...
thingiverse
PP3DP UP Plus and UP Plus 2 are usually terrible with printing PLA. Three major issues with these printers are 1. The throat of the hotend gets too hot as heat creep up the steel tube and the PLA starts to bulge there and gets impossible to reliably...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: holeRad = 5 radius = 15 build_plate_selector = 0 Font = write/orbitron.dxf edge = 5 length = 100 tagH = 20 width = 50 build_plate_manual_y = 100...
thingiverse
Remove the platforms callibration cable before printing Instructions Mounted with M4x16mm CHC Screws exept for hinges mounted with M4x16mm H Screws Remove the platforms callibration cable before...
youmagine
Replacement filament spool holder for the UP Plus / UP Plus 2 Clips on instead of original one, filament spool rolls on skate bearings (608). ... Print holder (on the side) (100% infill, 5 perimeters) Print clip (holes up) Clean support slide 5-7 608...
thingiverse
Replacement filament spool holder for the UP Plus / UP Plus 2 Clips on instead of original one, filament spool rolls on skate bearings (608). 1. Print holder (on the side) (100% infill, 5 perimeters) 2. Print clip (holes up) 3. Clean support 4.
thingiverse
... this filament holder and guide. ...This is for full size spools. Works really well guiding the filament. This would also work with other printers like the MonoPrice Mini with some modifications etc. Printed on an UP Plus from Tiertime. ...PLA
thingiverse
Hell, here is just a cuting piece of the big arm and mainbase for be printable on my Up! Plus2 You need glue ! ...
thingiverse
This is just a remix of this great spool holder but with screw holes instead of the clip so it can be used with the enclosure kit for the up plus 2.
thingiverse
Spool holder for a Dremel 500g PLA spool to fit UP Plus 2. They have started selling the Dremel 3D printer at Bunnings here in Oz. The filament seems to work OK - a few tricks to get PLA working with the UP (email if you are stuck). It's not...
thingiverse
Note Normal Temperature for Up Plus 2: ABS 260 deg PLA 200 deg Parts required: 1 xRotary Switch 1 pole x 12 way http://www.jaycar.com.au/productView.asp?ID=SR1210 1x knob http://www.jaycar.com.au/productView.asp?ID=HK7764 11 x 1ohm .25w resistors 1...
cults3d
Note Normal Temperature for Up Plus 2: ABS 260 deg PLA 200 deg Parts required: 1 xRotary Switch 1 pole x 12 way http://www.jaycar.com.au/productView.asp?ID=SR1210 1x knob http://www.jaycar.com.au/productView.asp?ID=HK7764 11 x 1ohm .25w resistors 1...
prusaprinters
Up Plus 2 Temperature Controller, gives your printer greater control of the nozzle temperature. Temperature can be changed while printing. Eg you can print the first layer at a hgher temperature to make it stick to the platform better. Note Normal...