upgrade anet pk8 3d models

Caution 2: For users with the stock Anet A8 frame, employing the "A8_Stock" carriage is recommended. This modification will result in a loss of approximately 2cm of printing area along the X-axis. Warning 3: It's essential to use LM8UU bearings in...

Warning 2: If you have the stock Anet A8 frame, use the "A8_Stock" carriage for optimal results. Be aware that you'll sacrifice about 2cm of printing area along the X-axis. Warning 3: The carriage requires LM8UU bearings for proper function. IGUS...

Remix of the original LED Lamp for Prusa I3 MK2/S, but for Anet A6.Great cheap lamp for your 3D printer, with lots of light.Uses cheap car interior panel LED lights commonly found on on the eBay.For full instruction on print and assembly, see...

Video guide: Text guide: https://e3d-online.dozuki.com/Guide/Convert+your+stock+Anet+A8+to+the+Hemera+toolhead/131#s1512 Get the ready-to-go firmware here: https://toms3d.org/wp-content/uploads/2019/11/Marlin2-source-A8-20191129.7z...

Additional parts needed for the mounting frame include: 3 - M3 nuts that are press-fitted into the frame first 4 - M3x8mm SHCS screws that secure the frame to the PSU 3 - M3x16mm SHCS or Phillips screws that attach the Frame/PSU combo to the Anet A8...

Subscribe Now!!!\r\nWatch This Video at https://youtu.be/V-q_PJ_qY5Y\r\n\r\nTop Upgrade Still Available!\r\nGet It Here: https://www.thingiverse.com/thing:2770619\r\n\r\nBearing Options:\r\nCheck Them Out on Amazon at http://amzn.eu/d2HUwX9

... ... Top upgrade available at https://www.thingiverse.com/thing:2770619. Filament spool holder can be found at https://www.thingiverse.com/thing:2070272. ... Bearings and rodamientos are available on Amazon at http://amzn.eu/d2HUwX9.

Upgrading to a Custom Spool Holder with Maximum Efficiency. The design centers around minimizing material usage while maintaining functionality. A note-worthy aspect is that it doesn't automatically print infill on bottom layers in Cura, yet still...

I took a preexisting cover design (https://www.thingiverse.com/thing:2320216) and modeled it to fit the PSU above. Additional Frame Components: 3 - M3 nuts - press fit into frame first 4 - M3x8mm SHCS - Mounts frame to PSU 3 - M3x16mm SHCS or...

......My Anet setup has a low build plate, which makes the original anti-wobble mods useless since they wouldn't allow enough clearance to print on the bed without hitting the couplers' top. This remix addresses that issue by simply enclosing the screws.

This heatsink support tube design will eliminate unnecessary bending tension on the empty side of the Anet A6's extruder caused by screwing solutions. *Don't forget to multiply the object or print it twice, as you'll need two tubes - one per screw.*...

In the **Anet A8 and similar 3d printing extruders** the cooling fan is screwed with only the bottom two holes, this makes the fan **poorly fixed** and prevents it from being fully screwed since screwing it too much leads to it bending and separating...

The Anet A6 kit has exposed main power terminals that pose a hazard, lacking protective covers, fuses or an on/off switch. Installing this simple power supply cover will significantly enhance the safety of your 3D printer operations. To assemble...

I Recently Upgraded a Smart Filament Guide and Filter Design, Enhancing Its Resistance to Fatigue Stress Caused by Retraction. The Original Design Was Found on Thingiverse as #2524232. It Had Been Printed Successfully Earlier, But Further...

In my adaptation of the upgrade plate, featuring the original fans and an 18mm capacitive sensor, I drew inspiration from various other projects. Unfortunately, there were errors in my previous design; I aimed to place the sensor at the lowest...

Printer settings: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution: 0.25 Infill: 15% I designed this project with precision and attention to detail, ensuring everything fits perfectly together. It was one of my most challenging projects yet,...

Having an Anet A8 you will notice the front and rear Y plates start to bend due to belt tension. Much cheaper and faster to print than an AM8 frame. Cost is about $10 in threaded rod, nuts and washers. Printable in about 6 or so hours. With this...

Safety First!The Anet A6 kit has dangerous main power terminals exposed without cover, fuse or on/off switch. This simple power supply cover will make your 3D printer more safe to operate.</p><p><strong>To assemble you will...

This is my updated upgrade plate, featuring the original fans and an 18mm capacitive sensor. It's based on a few other projects, but I made some critical mistakes in the previous version that needed correction. My goal was to position the sensor at...

The good news is that this upgrade is incredibly easy and doesn't require any major changes to your printer setup. What I did was take the base of the original box and use it as-is, while modifying the cover to fit my needs. To give you an idea of...

To prevent damage and potential breakage to the X gantry data cable, upgrade its design to avoid movement at the board connector when the Z axis is in motion. The X stepper's backplate is secured using 1mm thick sponge-like biadhesive tape. It's not...

... a 6A fuse, but feel free to consult with a proper electronics expert in your area. Print Settings Printer: Anet A6 Rafts: YesSupports: No Resolution: 0.2Infill: 100 Notes: Printed at 0.2 or 0.1 and 100% infill. ... Category: 3D Printer Accessories

... detailed assembly instructions, refer to "assembly1 and 2." As this modified blower setup allows for increased airflow, users may need to reduce their blower output accordingly. With this upgrade, you'll be able to enjoy smoother printing results!

110V users probably want about a 6A fuse, but feel free to consult with a proper electronics expert in your area. Print Settings Printer: Anet A6 Rafts: YesSupports: No Resolution: 0.2Infill: 100 Notes: Printed at 0.2 or 0.1 and 100% infill. ...

The Anet A8 receives a critical upgrade with the installation of an endstop system based on the PK8 frame, which replaces the traditional mechanical switch with an inductive probe. ...This innovative solution provides enhanced precision and reliability...

Tight-fitting cap designed to fit snugly over the 2040 I-Type slot 5 aluminum extrusion.

<p>This is my BIQU H2 Mount i designed with CR-Touch Mount<br><br>More Designs coming Soon.</p>

Stabilized, perfectly luminous frames are a model of perfection.

To center the Fillament spool weighing 37g, insert the default spoolholder stably. A simpler process can be achieved by using an additional part found at https://www.thingiverse.com/thing:3794506. For those who want a reduced print time, there is...

Annoying connection with reset button in middle of print? Quick fix, tiny ring glued with silicone - didn't use superglue due to risk, adding some on the button itself for extra security. Easy solution for the Z-axis belt, now working way better as...