upgrades for ender 3 v2 neo 3d models

It is just a tool holder for the Ender series but with a sliding mount instead of press-fit, and some SD/microSD card slots.Minimal supports needed, just for the sliders.

Design of the tool drawer should work for Ender 3 v2 as well. The design is intended to use the original "case" for the tool drawer but for my method of implementation holes need to be drilled into the case for wire routing. A drill pattern in...

For the fan I used an noctua NF-A9x14 PWM but other 92mm fans should fit as well. The part is designed to print with a 0.6mm nozzle. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 300 Infill: 38 Filament:...

Ender 3 cover

... near by and hadn't found anything I liked, so started learning how to use Fusion360 and designed this. ...It slides into the rails on the bottom of different Ender 3 models. ...I found it printed best from a corner, with a small raft and supports.

سلام عليكم this is a prototype, i share .f3z file for remix or upgrade for now its working fine and easy to install just need screws M3 to hold it the point of this design that you can level it with the nozzle touching the bed i hope its help with...

سلام عليكم this is a prototype, i share .f3z file for remix or upgrade for now its working fine and easy to install just need screws M3 to hold it the point of this design that you can level it with the nozzle touching the bed i hope its help with...

I only used this for tuning input shaper, then removed the mount.This model uses the space from here: BLTouch Spacer/Screw Cover for Ender 3 Pro by onpdm - ThingiverseI don't have a photo of it mounted, I'd removed it and started a new print by the...

Cover for the Ender 3V2 Display. I recommend printing the frame in an upright position with supports enabled in order to make the snap fit work better. ... After assembling you can mount it with double sided tape to the screen as shown in the picture ...

upgrade if you only have the stock fan housing, this will be the way to go

Remixed from: https://www.printables.com/cs/model/115518-biqu-h2-ender-3-v2-mounting-plate-with-bltouch Intended to be used with: https://www.printables.com/model/114869-biqu-h2-extruder-part-cooling-duct-mount and...

... on the back. PLA seems to work best, as it is stiffer and this part wont see heat. You might also find printing the slide at 101% size makes it fit REAL nice.This is a remix of “Ender 3 Adjustable Endstop (3 and 3 Pro)” on thingiverse by Mach_Zero

Case for Ender 3 / 3 Pro / 3 V2 in the "Minimal" style. ...Included is a file with a case cover with holes for better cooling and reduced fan noise.

Полностью переработанный адаптер с выходом нагретого воздуха через штатное окно каретки Ender-3 NEO без потерь области печати и работы зонда. Правый воздуховод изменен под размещение Cr-touch. Позиционирование проставки и воздуховода на столе при...

This is a remix of https://www.thingiverse.com/thing:5179838This remix takes the mount the fits the Ender3 V2 hotend shroud and modifies it to fit a Mitutoyo 2046 dial indicator. ...The mount is a direct replacement for the rear cover of the dial.It...

Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot

... for the heater cable). I also reinforced some areas a little and enlarged the mount holes at the front to better accommodate the coarse fan mounting screws. Fully compatible with the CR Touch that comes with the stock Neo (and Neo v2). ...

I accidently printed this thinking it would fit my V2 (I know I didn't read his description) So I made this fit. Just elongated between the two semi circles. Fit snug for me. I may remake this and make it a mm or two longer if there are too many who...

I didn't yet drill a hole for the power cord (I just pass it through the bottom doors) but it may be a nice extra upgrade. Maybe I will also print some handles for the bottom doors. ... **List of parts:** - Platsa struture 503.309.46 - Värd glass door...

I didn't yet drill a hole for the power cord (I just pass it through the bottom doors) but it may be a nice extra upgrade. Maybe I will also print some handles for the bottom doors. ... List of parts: - Platsa struture 503.309.46 - Värd glass door...

... connect to biqu 2. lossen the gantry wheels(only need a few mm) and plece the mount under the screw 3. connect to the plate with 2 m3 and then tighten the wheels screws update-19.6.22: top and bottom screw holes are now slots for easier alignment

... screws. For those who need it, the case for the SKR 1.3 is available at https://www.thingiverse.com/thing:3717627. ... Big shoutout to Dasgrinch for creating a left side version remix - check it out at https://www.thingiverse.com/thing:3944663

This is for an Ender 3 Neo with the extender 400 ender 3 pro kit . you will also need feet on the printer, I got mine here https://www.thingiverse.com/thing:5522084 . This is designed to house the 4.2.2 mainboard and a 120mm thin fan . I am hoping I...

tool holder for the tools supplied with the ender 3 + a cutome case

you can replace this with the cap of the original spool and have a double spool as well, its width is 3 cm so any filament can fit

Remix of https://www.thingiverse.com/thing:4604339Wanted to make it fit a Pi 3 A, so moved screw holes and changed usb slots.To print, follow his guide.

Simple case for Electreeks® Raspberry Pi Kamera

Cover Qr code modelize with a bmw logo for the fans of the brand.

Needed a place to mount an ADXL345 for use with Klipper, so I made this simple remix. ... You'll need to tap the holes for the ADXL345 to use short M3 screws to mount it.

Bed leveling bushing to remove springs. ...I have also added a extra 17mm tall bushing for the cable tray on the back of the bed.