upgrades for ender 3 v2 neo 3d models

Designed to fit Creality Ender 3 V2 Neo but can be used as standard container without attaching the rails. ... 2 container sizes (mm): 135L x 40W x 25H and 135L x 40W x 40H Caution: When used on printer, keep all items below build plate surface to...

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

... I'm not entirely sure if the dimensions of the profiles changed between the original Ender 3 and the Ender 3 v2 Neo, but at least on my unit, the slots in the profiles do not match the dimensions in the blueprints available from Creality on GitHub.

I made this to relocate the Ender 3 V2 neo x-limit switch to support the Sprite Pro extruder which will not trigger the X-limit switch in the default location. You reuse the original screws and the limit switch and need to add two M3 bolts and nuts...

You can also raise the camera itself -after mounting it- for your liking.Print SettingsCreality Ender 3 V2 Neo - using Cura + Filament Friday Extra Fast 0.28 profile with 10% infill. Important: Print with a brim to help with adhesion. ...No support...

They have a length of 44.5mm without the extrusion slots and should work with the stock feet of an Ender 3/v2/Neo but I have also added spacers that can be placed under the feet which can be scaled in a slicer and I have added the .f3d file of the...

I made these feet to support the Y-axis on my Ender 3 v2 Neo to increase speed and acceleration.They require no additional hardware and can be easily installed by removing the four screws holding the Y-pulley tensioners and sliding the feet onto the...

Ender 3 V2 Neo is my first 3D printer. I bought a 2KG spool only to find it was too wide to fit on the stock spool holder. Started learning sketchup so decided to recreate the stock spool holder but make it about 15mm longer. Worked pretty well,...

I've colour matched my LED to the one that's included in the Ender 3 V2 Neo CR touch to make it extra snazzy, Just screw mount the Raspberry Pi to the drawer base. I used recessed M2.5 screws that screw into a heat-sink from the bottom up. Then it's...

This support has been designed for those who, like me, own an Ender 3 V2 Neo and have added a Creality filament end sensor. Impossible to find on platforms so I designed a perfectly functional one. This pack includes: Stand The pulley The screw...

This is a direct replacement hotend cover for the Ender V2 Neo. It works with the standard fans only. It lines up with the blower fan intake better than the original. I added 4 LED's to the eyes and below to light up the print area. I use 2k ohm...

Ender 3 v2 led top and side led bar The installation was made with a 1 meter led 5050 strip

Remixed from https://www.printables.com/model/270817-ender-3-v2-extruder-cable-guide Supports needed. ... It's very tight

Modification of the E3V2 design to fit specifically the Ender 3 V2 Neo Recommendations: a) Connecting the autostop switch in parallel of the printer switch (i.e. ...connecting both switch pin to pin), and not serially (as suggested in the original...

All credit goes to the original creators - I simply added a couple features and modified them to fit my printer. This was designed for and tested on my Ender 3 V2 Neo with a Spider 3.0 Pro hot end. UPDATE: I started having issues with getting a good...

I was tired of digging in the drawer for my Allen Wrenches... ...So, I made an Allen Wrench holder for the wrenches in the kit that comes with the Ender 3v2 Neo. ...Fit's on the top of the printer and is held in place by a T-Nut and a Cap Screw.

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

this is mount works for the ender3 v2

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

My Neo had a different bar layout to what this file required, so I modified the file slightly to fit. All other attributes are the same as the original file. ... You will still require a long ribbon cable.

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

Same thing, adapted for Ender 3 v2 Neo.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I was searching a simple and easy duct for 5015 blower upgrade, lot of complicated designs out there. So I designed my own. It uses stock screw and attachments, doesn't mess with heat cartridge wires, and you have room to regulate distance from...

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

This mount is for if you have modified the printer to a direct drive extruder and the filament routes up.I wanted a reel mount that would fit in my enclosure without impeding the side wall, allowing me to centre the printer.I printed each piece...