us 8 150w rack mount 3d models
785537 3d models found related to us 8 150w rack mount.thingiverse
10 inch rack mount for UniFi US-8-150W. Required 2 pcs. ...square nuts rack.
thingiverse
Modified: https://www.thingiverse.com/thing:3230275 This one is stronger, makes for a more sturdy mount.
prusaprinters
<p>Print in PETG, needs around 30% infill 3 walls to make it sturdy enough.</p>
thingiverse
This is a remix from Labol. ... I added some material where you attach it to the rack, so it's 4mm instead of 2mm thick. ... I also made one small rack ear for the other side as well, because i didn't have the original one.
thingiverse
### Ubiquiti UniFi US-8-150W VESA Mount Mount a UniFi US-8-150W Switch on the Backside of a TV to the 200x200 VESA Mount.
prusaprinters
Ubiquiti UniFi US-8-150W VESA Mount Mount a UniFi US-8-150W Switch on the Backside of a TV to the 200x200 VESA Mount. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 25% Category: DIY
thingiverse
Unifi 8 Port 150w Rack Mount for a 19in rack. Print 2 pieces one for each side. ... Update 02/12/2020- Added a support bar in the middle to give it a little extra strength.
thingiverse
A server rack mount spacer for the UniFi Switch 8 (150W). This allows one to mount the switch in a full width (19") rack. ...The model supports the original hardware provided with the switch.
prusaprinters
Spacer that allows me to mount my UniFi switch on a full width rack. Print instructionsPrinted using Slic3r defaults for .2mm Generic PLA.
cults3d
This design helps manage the cables for the router. ...10in threaded rods and nuts used to connect the cable management halves and the rear fan mount to help cool the router. ... The fan mounts are for 40mm fans.
cults3d
Another design for this router. ...It is unfinished as there was supposed to be a bracket to mount 40mm fans to on the back. Please message me if you're interested in the fan mount, and if you buy these files I will complete the fan mount for free.
cults3d
This design incorporates cable management and a fan mount for two 40mm fans to help cool this router, as it is known to get quite hot. ... If the bracket is too large, for your printer, just message me after purchase and I'll send you over a split file.
thingiverse
**** Update v1.4 **** J'ai rallongé les traverses arrière, et ajouter 2 trous pour fixe la braquette qui est retirer. En plus ca redonne de la solidité I lengthened the rear cross members, and add 2 holes to fix the bracket which is to be...
thingiverse
Remixed a good support design but with the Ubiquiti logo recessed in Fusion 360. Updated to add various files: left side orientation, right side orientation, and one reversible with logo removed. ...
thingiverse
Parts to stack Ubiquiti Networks Unifi US-8-150W POE switches. ... I printed these with 20% infill and no supports.
prusaprinters
I whipped this up in Fusion 360 to be able to rack mount my US-8-150W in to my network rack. I know there are some models out there already but I wanted the practice.</p><p>Over time, the switch does sag but not too much. I do recommend putting...
thingiverse
Patch Panel bracket for Unifi US-8-150W Switch for 19 inch Rack with 6 Keystone Sockets. ...
thingiverse
A rack mount to install a Edgerouter X next to a Unifi Switch 8 150W in a 19" rack.
prusaprinters
Unifi US-8 1U 10" Rack mount.Printed i PET-G.You will need a M5 screw for the hole in the back
thingiverse
I've remixed the mounting bracket so it can be put onto the wall with double-side tape (Tesa brand recommended)
thingiverse
This is version 2 of my Unifi US-8-150W cooling solution. The original works well, even better if you tape up the remaining holes in the rear of the device. This design allows for complete coverage of the perforated part of the rear panel. ...(no tape...
thingiverse
Bei meinem Unify Switch US-8-150W ist das Netzteil ausgefallen, darum habe ich nach einem Ersatz gesucht. Das EPP-150-48 passt perfekt, ist aber von den Maßen her deutlich kleiner als das Original. Darum habe ich diese Halterung konstruiert, wichtig...
prusaprinters
Ich hab das mit einem kleinen Schraubenzieher gemacht.EN:The power supply failed on my Unify Switch US-8-150W, so I was looking for a replacement. The EPP-150-48 fits perfectly, but the dimensions are much smaller than the original. That's why I...
thingiverse
The original 1/2 19in rack mount I found held a Unifi US-8 and there was a matching 1/2 19in blank mount to round out to the full 19in. The middle connection point is sturdy and the Unifi model was spot on. My initial test print came out great so I...
cults3d
The original 1/2 19in rack mount I found held a Unifi US-8 and there was a matching 1/2 19in blank mount to round out to the full 19in. The middle connection point is sturdy and the Unifi model was spot on. My initial test print came out great so I...
thingiverse
This is a Remix of the Ubiquiti USG part from the original for the 8 Port POE Switch of Ubiquiti. Printing in PETG should be better because the switch gets very warm. This is still in Project, i did not print it yet. Maybe you can comment if it...
cults3d
This design is for cable management for this router. ... If your printer is too small for this, please see the regular Version 2
thingiverse
This thing is an adapter/mount to secure an Ubiquiti EdgeRouter X and Unifi Switch 8 150W in a 19-inch 1U rack slot. The mount can be installed to either side of the switch. The EdgeRouter X has to have the rubber pads removed to fit into the slot...
thingiverse
This is a solution I designed to keep my Unifi US-8-150W switch cool. From the factory this switch runs very hot due to being passively cooled. (77c in my case!) This duct slides over the case of the switch and sucks air through it. I designed it...