usb 3.0 header 3d models

USB Holder design for Ender 3 v2, but can also be used for Ender3 and Ender 3Pro. It screws on down-left corner of the printer. ...If you have problems while you downloading files with ERROR 404, go to "thing files" right below and and click on...

Thanks!! Created in Fusion 360. Here is the USB cable I used: https://amzn.to/2NxpBmu USB cable attaches with 2x 12+mm M3 bolts + nylock nuts. I did cut down the tabs by about 1mm to make the USB port flush with the 3D Print. ...I also drilled out the...

0.6mm x 0.4mm lead width,2.54mm lead spacing,footprints: 6-Way: 15.64mm x 2.5mm,8-Way: 20.72mm x 2.5mm,10-Way: 25.80mm x 2.5mm

This product boasts a dimensions of 3 inches by 11 inches and features four functional ports for your convenience.

Asuka - Evangelion 3.0+1.0 Movie Thrice Upon a Time 🎉Get ready anime fans! Join our Patreon now to get access to this month's 3D printing STL files, and as an early supporter, you'll also get access to all the figures from the previous month!

Around that is a yellow square to create a neat hole.The blue bit is removed to allow a 1x2 dupont connector to be connected to the GPIO24 and GND pins (pin 18 and 20 on the header).The black is a bit of embossed text. A fine print resolution is...

Fixing a Mini USB Port on Your Creality Ender 3 Printer If you're looking for a quick fix to seal up that tiny gap on your Creality Ender 3's Mini USB port, then look no further. This nifty little solution is perfect for sealing small holes and...

**Extrusion Settings Optimization:** Under specified settings, extrusion widths are carefully set to reach precisely 0.3 across. 4. ...**Base Shape Refinement:** Careful adherence to initial input dictates that our creation adheres rigidly to the...

ATENTION: THE APPLE TV NEEDS 3.4V AND NOT THE 5V SUPPLIED BY USB. YOU HAVE TO USE A SMALL DC-DC CONVERTER (which you can buy very cheaply online) AND TUNE IT PROPERLY. I DON’T TAKE ANY RESPONSABILITIES IF SOMETHING GOES WRONG HERE. IF YOU WANT TO...

Update: I forgot to add that you'll probably need something like this right angle USB adapter to make the USB port supplying the hub face down instead of out: https://www.amazon.com/gp/aw/d/B07QYS3FD8 Update 2: I added some new photos showing better...

http://www.thingiverse.com/apps/customizer/run?thing_id=1241205 Instructions Using the following options: line_3 = production dferraro = line_1 plate_depth = 10 mm text_size2 = 11 points text_size1 = 15 points plate_height = 40 units...

Just a mount to replace one of the aluminium profile caps on the ender 3 with a usb port so you can power your rpis or cameras from it! You will have to open up the covers to get access to the power supply unit of your printer to get the 24V...

Easy Plug and Play USB Support USB devices are plug-and-play ready out of the box. ...No additional software installation is required to get started.

USB holder with T-nut and screw from the ender printer kit.

Holder for usb card reader. ...Will add screw caps at later date.

Replacement endcap for 40x40 frame to allow handy access to USB drive

USB cable rack. With and without screw holes. ...Print without supports.

You can hook up a cheap USB microscope to your Ender 3 printer. The idea is that this setup can do several things: 1) Position the microscope precisely and repeat it for accurate results. 2) Level the bed automatically so you don't have to do it...

This contraption slips neatly into the Ender3 spool holder, securing my trusty USB SD card reader from getting misplaced.

This usb sleeve was made in fusion 360 it is a tight fit no glue required go's on any usb that comes with a creality printer looks good and helps to keep dust out and give your usb some protection.

I wanted something to put the usb in, since I always have it lying around and I'm afraid to lose it, I found the version of tstaubs1, but I wanted one that would allow me to insert the entire usb, with the cover included. So I made this modification...

This is the plug that goes into the motherboard for USB 3.1 Gen 2 10 Gbps into either USB 3.1 Gen 1 Key-A Unshielded Header or USB 3.1 Gen 1 Key-A Shielded Header

This is a remix of two designs. ...I took the USB holder from the tool holder design and one of the rails and mashed them together.

This innovative 3D printing design boasts an impressive capacity to store up to twelve SD memory cards and three USB devices simultaneously.

This versatile USB key holder serves as an ideal accessory for USB SD card adapters, ensuring they are always securely stored and easily accessible. ...Its parametric design allows users to customize the model to suit their specific 3D printing needs,...

... text: Useful clip to help keep track of your USB sticks and SD cards. ... I've remixed some cable clips that can securely store an SD card or USB stick inside them. ...For optimal results, I recommend printing them on their side with supports enabled.

A quick reference guide to remember the nozzle mounted on the printer head: 2 clips with a diameter of 8 that attach to the smooth rods One for the 0.3mm nozzle and the other for the 0.4mm nozzle

A Megatronics 2.0 shielding case provides safety and security for your valuable gadget. ...Safeguard your investment with this reliable enclosure designed specifically for Megatronics 2.0 devices. ...Keep your technology secure and protected with ease.

Rewritten text: For an individual pursuing a career in electrical engineering, this content is particularly relevant and insightful.