usb c cap 3d models

The reason for remixing it was to accommodate the specified converters on eBay at http://www.ebay.nl/itm/3Pcs-USB-3-1-Converter-Type-C-Male-To-Micro-USB-Female-Adapter-Data-Connector-/122444504058, which necessitated a re-scaling of the original...

Since I prefer using USB-C cables because they are relatively inexpensive and easy to replace over time, this device keeps the cable securely attached to the brick at all times even when it slips off. It's more convenient for me to place the long...

Charging board link: https://www.aliexpress.com/item/1005004645663172.html?spm=a2g0o.order_list.order_list_main.141.52e91c24foiV6z&gatewayAdapt=glo2pol (QC4.0 QC3.0 LED Dual USB PD Fast Charge 5A 100W Micro/Type-C USB Mobile Power Bank 18650...

I believe it should fit all variations of the 1.3 hardware (except the "Pro" variant) but the micro USB version will have a gap around the port as a USB type C port is physically larger than a micro USB port.I printed the bottom housing as-is and the...

... as it is shown in the photos. 2. Put XT60 and trigger board inside bottom piece (no USB-C hole) and solder it together right inside of the bottom piece. 3. ...Snap upper piece on bottom piece while leaning upper piece against one of bottom's edge.

Simple box to house the ZY12PDN USB-C PD Trigger. ...I use it to power some of my 9V retro computers and have put the trigger inline with a switch.</p><p>Holes in the lid for access to the voltage change button and a small opening so you can see the LED...

I purchased an excellent little USB C Hub from AliExpress that solved my previous problem with loose connections. The hub's sturdy design prevents it from wobbling or disconnecting when I move the computer. Additionally, it elevates the laptop...

The original design had dimensions that did not fit my USB-C cables. The "knobs" had tiny attachments to the rest of the model and would break away easily. And, the other model was a mess on the inside, with weird features causing print artifacts on...

This is a mouting plate for the Anker USB-C Docking Station PowerExpand A8392. Without this plate, it can easily tip over from its veritcal position. This little plate can be affixed with doublesided tape or screwed down to the mounting surface and...

Added spool and cable lock for TS101 USB-C standard cable. The hinge remains the same but for the hinge pin, use a 1.75 PETG (for better durability) filament. Slightly heat with a lighter and insert the filament into the hinge and cut excessive...

... me behind schedule. However, I did successfully print V1, but made an error regarding the USB-C port's location, which needs correction with V2. ... Additionally, if anyone knows how to rotate images within Thingiverse, please share your insight.

This is just a small protective case for my MP07-IONA-US, the version with the USB-C power port. The lid snaps on and the board is screwed into the bottom using short M3 machine screws. Mine were around 8mm or so, but they really need washers or...

• USB Cap Dimension: Measuring One Point Two Five Units in Height. • Sign Design Choice: Selected as Option Number 1 Preference. • Device Configuration Order: Ranked at First Position Sequence. • SD Card Unit Quantity: Determined at Four Count Value....

https://www.thingiverse.com/thing:2467743/files I've modified the base to incorporate a USB C connector for powering the servos and, optionally, to power a camera board or anything else attached. The included file is for the base only. All...

## MiSTer USB-C Power Delivery dongle Clean up some cable mess and replace your weird "lamp" style switch with this USB-C power delivery dongle. This simple and inexpensive design lets you use modern USB Power Delivery compliant phone/laptop chargers...

A Tiny USB Type C Adjustable Power Supply is Made Possible with a PD Buddy and a DPS5005 Adjustable Power Supply. Both Devices Can Deliver up to 5 Amps of Power. While the DPS5005 Supports a Maximum Voltage of 50 Volts, USB Type C only Goes Up to 20...

This adapter fits the ZYPDS USB-C 20V adapter. https://www.ebay.com/itm/Super-Mini-ZYPDS-DC-mini-20V-trigger-support-millet-65W-PD-power-supply-/132714794782 Allowing you to power your thinkpad with a modern 65W 20V 3.25A charger or powerbank. Red...

Plugging your phone in for charging compacts this lint at the bottom of the port, which can lead to unreliable charger connections. This tiny tool is designed to remove compacted lint from the bottom of your USB-C port. Its hook is thin enough to fit...

A tiny adjustable power supply that uses a PD Buddy to source power over USB Type C and a [Rui Deng] (https://rdtech.aliexpress.com/store/923042) DPS5005 adjustable power supply does the adjustment. Both support up to 5A, and while the DPS5005...

This modification is specifically designed for the DAN A4-SFX computer case, allowing you to swap out the USB 3.0 Type A connector for a more advanced USB 3.1 Gen 2 Type C connector. I employed the Lian-Li PW-IC01NH45 cable (http://bit.ly/2fvjwCV),...

This is a keychain designed to hold a small USB-C to microUSB converter, allowing users to take advantage of the new standard for Nexus devices while easily accessing any microUSB cable. I'm drawn to the idea of drepamig & Sach's keychain holders,...

This is a small clip designed to attach to a charging cable and hold a silicone USB C dust cover while a smartphone charges.Silicone dust covers are a great way of preventing dust from getting into your device's USB port while it is in your pocket,...

<p>Printed on CR10V3 with PLA. ...Tool at 195°C and bed at 60°C.

A tiny adjustable power supply that uses a PD Buddy to source power over USB Type C and a [Rui Deng] (https://rdtech.aliexpress.com/store/923042) DPS5005 adjustable power supply does the adjustment. Both support up to 5A, and while the DPS5005...

&nbsp;Decided to mod this to accept a usb-c cable for power, and took a bit more time to add spots to store the stirrers when not in use.&nbsp;What is needed (amazon links offer rev share to me, I appreciate your support):This Specific Magnetic...

This is a custom cable protector designed specifically for the USB-C cable that comes bundled with the Nexus 5X smartphone.\r\n\r\nTo print this design, use 100% infill and avoid supports altogether. Its snug fit requires careful insertion of the...

This is a simple design for a USB-C power bank with 18W fast charging. You can build it with 4, 6 or 8 18650 cells. Get all info about this build and how to assemble it from my video! https://youtu.be/lP944BiACvY You need to print: 1x Shell ...

the t4056 is USB C module and fit the PCB place nicely, easy enough to remove and replace prior to glueing. I plan to add a cover for the PCB at a later stage. (post few tests that still need to take place) Printing: I'm printing this with 3...

Panel mount for a 30w USB Type-C board generally found on Aliexpress / eBay, with a cutout template to cut your panel. I used this in my Powerbank / Solar generator build. Important: It was designed to be fastened with a zip-tie, don't forget that...

Adopting the Type C standard for projects can be a challenge, which I encountered in a diy airplay amp project. I wanted to use the 20V power supply with a USB-PD wall plug, but found it quite difficult to locate a panel-mount friendly way to do it.