usb sniffer 3d models
50541 3d models found related to usb sniffer.thingiverse
Basic enclosure for the OpenVizsla. Dimensions taken (sloppily) with calipers rather than going from the design files, so aren't spot on, but it's still not a bad box and will help give some protection. Tested in ABS; I wouldn't expect any...
thingiverse
This is a protective case for the Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 USB stick. Just print and insert your USB stick. This model might fit to other USB PCB sticks as well. Take care of the tolerances. You might need...
thingiverse
Case for CC2530 and TTL modules for use with Zigbee2MQTT Boards available here https://www.aliexpress.com/item/CC2530-Zigbee-Module-UART-Wireless-Core-Board-Development-Board-CC2530F256-Serial-Port-Wireless-Module-2-4GHz/32767470382.html...
thingiverse
The 2022 mob vote winner, missing the leafy object on its back, tinkercad is hard to work with
thingiverse
Model of a Bacharach 300 sniffer. ...Use is highly technical.
thingiverse
Un Sniffer con nervios para proporcionar algo más de dureza y evitar su ruptura.
thingiverse
I used a prestone coolant tester for the bulb, and some flexible tubing and brass rod for the "sniffer" part. For the strap I used the old waist strap from my spirit pack. Hope this helps the GB prop building community. Maybe even someone with better...
thingiverse
Remix of Gatsu logic sniffer case (https://www.thingiverse.com/thing:16033). On my printers buttons cannot be printed so i added flexible parts for pressing buttons on the board. ...Added a hole for the pin header too
thingiverse
You will need: 4" Female Schedule 40 PVC Closet Flange 4" Schedule 40 PVC Pipe (Solid or Foam Core) 9" Long 4" Schedule 40 PVC Female-Female Coupler 4" Schedule 40 PVC Male to 2" Female Reducer 2" Schedule 40 PVC Pipe (Solid Only) 3" Long (Base to...
thingiverse
A housing for the Open Bench Logic Sniffer. ... Instructions http://dangerousprototypes.com/docs/Open_Bench_Logic_Sniffer Made from 4mm fluorescent Acryl, partially glued, finally screwed using M3x14.
thingiverse
I have some generic IR line followers, and wanted to adapt the sniffer holder for them.
thingiverse
I have done the following: 2.5mm nut sockets underneath 2.5mm bolt head recess slightly on the lid Increased the size of the USB port hole to fit my cables Finishes nicely with some rubber feat or some adhesive foam. I used a bit of thin adhesive...
thingiverse
Reinforced version of Renacuajo Sniffer. Adapted to connect linefollower sensors. ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
The PCB slides inside the shell, then the cap covers the side where the USB receptacle is and is mounted with two M2x4-10mm countersunk screws. There is an optional LED diffuser which can be printed using transparent filament. It fits snugly, but I...
thingiverse
If you got your Open Bench Logic Sniffer from Dangerous Prototypes http://dangerousprototypes.com/open-logic-sniffer or Gadget Factory http://www.gadgetfactory.net/gf/project/butterflylogic/ you might found that with unprotected underside working...
cults3d
... case for fingers. Full instructions with more pics here:http://www.built-to-spec.com/blog/open-bench-logic-sniffer-enclosure Get a kit here:http://builttospecstore.storenvy.com/products/2107326-open-bench-logic-sniffer-enclosure Design by RoboLemur
thingiverse
This is a case I designed for the VK3YNG MK4 transmitter hunting sniffer made in Australia. It's designed to fit on the end of 1/2" PVC pipe. Holes for screws are included to hold PVC pipe and make it easy to disassemble or modify location. Print...
thingiverse
Full instructions with more pics here:http://www.built-to-spec.com/blog/open-bench-logic-sniffer-enclosure Get a kit here:http://builttospecstore.storenvy.com/products/2107326-open-bench-logic-sniffer-enclosure Design by RoboLemur Instructions Cut...
thingiverse
Simple box case and simple 'frame' case for the Dangerous Prototypes Open Bench Logic Sniffer. The frame version uses very little material and the PCB provides most of the structural integrity. Both versions don't inhibit additional header pins etc...
thingiverse
This snazzy little number was put together to keep the Dangerous Prototypes Open Bench Logic Sniffer safe from stray desk detritus. It has a simple 6 piece construction and is assembled with 4 x 10mm M3 Screws and 4 x M3 Nuts. You'll want another to...
cults3d
This is a Print in Place model of this year's mob vote winner - the Sniffer! You can slide the legs out to lay the creature on its stomach, or push them half-way in to make it stand. The ears are floppy and the head can has two positions. This big...
thingiverse
This is case for the Open Workbench Logic Sniffer as sold by Seeed/Sparkfun/Adafruit etc. Instructions Lengthways the case is 99mm long, so if you are printing this on a Cupcake you will want to make...
thingiverse
It can be used as RS323-UART-USB in a way that you can Forward RS232-data to two USB-clients Sniff data between two RS232-devices, RX and TX at the same time. Modify during communication (man-in-the-middle) ??? ...You can find the files for soldering...
thingiverse
... open it up all of the way so that the plug can mate closer to the board. The design also precludes any need for support material, since the hole for the mini USB plug is open, and I have a 30 degree angle in the slot that holds the board in place.
pinshape
... open it up all of the way so that the plug can mate closer to the board. The design also precludes any need for support material, since the hole for the mini USB plug is open, and I have a 30 degree angle in the slot that holds the board in place.
thingiverse
Hi there! I made this model of the new minecraft mob called snffer in like 20 minutes, so don't blame me if there is any size errors :) You need 4 filament colours to print it: brown(red), yellow, green and black. All the colours have a different...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...