valve index extension cable 3d models

Cables: Club 3D DisplayPort Cable 1.4 Extension Cable 2 m CAC-1022 https://www.amazon.de/gp/product/B07RJ13CH9/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1...

A simple cable mount for Valve Index.

A small clasp to hold a Valve Index cable without slipping when using retractable cables for cable management. Place the two halves around the cable, push the center piece onto the two halves to lock it in place. ...The center piece will flex open to...

I was trying to attach the cable to the side of the headset, so I loosened the clip on the back (you loosen it by pushing the sides outwards) and created the clip. ...The clip must be held together with cable ties, three by the number.

Belt clip for valve index headset cable: a game-changer for comfort and convenience. The headset now feels significantly lighter, free from the cable's constant tug on the ground. To secure it snugly, simply press fit the cable into place. Before...

**General:** Designed this cable clip replacement for my Valve Index after the original one broke. It should be an easy replacement, as it was designed after the original clip. If it doesn't fit perfectly or you have tolerance problems with your...

Just slide this over the top Index strap, insert cable ties into channels on the side and wrap cable like on the first image and tighten down the cable ties. I used the cable ties that came with my Prusa MK3S, the dimensions for the cable ties are:...

Simply slide it over the top Index strap, insert cable ties into the channels on the sides, wrap the cable as shown in the first image, and tighten down the cable ties. I utilized cable ties that came with my Prusa MK3S, which have the following...

Cable saver for index. I made this after my cable started going bad. So I made this. Side effect is that it squished the current cable enough to use until the new cable gets here. This should in theory reduce the radius of the cables bends coming...

I made this cable guide to route the cable better when using an overhead cable management system and to allow the cable to flex over a longer section to reduce pinching. The tolerances are pretty tight so you may need to slice open the gap where the...

Using a ceiling cable management system can be super helpful, but be aware that the clamp can technically be installed almost anywhere. ... It snaps into place very securely, making it a tad challenging to take out without causing some damage.

Luckily, Valve made available the files for a grip extension, which they should have included as a molded part in the box from the start. Unfortunately, the inside of these extensions is designed like a honeycomb, making them difficult to 3D print...

This holder lets me coil up the extension cables and put them on the side of the desk (and importantly off the floor). To mount: You'll remove the "Uplift Desk" name tag on the left/right side of the desk. Then use 2x M4 bolts and nuts to attach....

This holder lets me coil up the extension cables and put them on the side of the desk (and importantly off the floor). To mount: You'll remove the "Uplift Desk" name tag on the left/right side of the desk. Then use 2x M4 bolts and nuts to attach. ...I...

This bracket allows you to mount the break away cable from the Valve Index to the underside or top-side of a desk.

A clip that keeps the split of the Valve Index trident cable held together (similar to the clip on the HP Reverb G1)

A compact little clip to keep the breakaway segment of the Valve Index cable securely attached to a metal surface. Featuring the iconic Valve Index logo because it's a nice touch. ... Required materials: 10x 6x3mm Disc Magnets Super Glue Print without...

This holder securely cradles the Valve Index cable, providing a comfortable fit that prevents it from dangling directly off your head. It requires two 1cm wide velcro straps to effectively keep the cable in place. ... I designed this model after trying...

Note: This and future projects are now available on Printables, see https://www.printables.com/model/165998-valve-index-rear-cable-clip-larger-hooks . ... This remix increses the size of the hooks, to make the clamp fit better when printed on...

I was scared to rip my gaminglaptop off the shelf. ... So i printed a protection for the Valve Index. It slips right into place and cable can still be taken off. I printed it with my Resin-Printer but FDM works fine as well! ... (Supports needed)

I was unhappy with the power cable routing for my Valve Index, so I designed a "turnaround" that allows the cable to enter the case and make a 180-degree turn, effectively converting it into a port. ...This modification requires four M2 x 6mm screws,...

Valve index breakaway cable management you can mount on your desk using double sided tape, there are 2 versions, for on top of your desk and below your desk. To mount I've used double sided 3M tape. Te keep the connector in place in the casing...

Valve index breakaway cable management you can mount on your desk using double sided tape, there are 2 versions, for on top of your desk and below your desk. To mount I've used double sided 3M tape. Te keep the connector in place in the casing...

This is a cable management gadget for Valve Index Dongles. It has 3 holes, so you can either put the cables through there, or use it to scew it on the wall. Print-Support is recommended for the bridges but not necessary. I'll try to upload a 8...

A flexible cable relief piece for Valve's Index. The headset's cable drops down from a hard plastic clip with no stress relief. So i made this flexible piece to try and save that part of the cable from eventually kinking. The part just slides into...

This is a remake of my old Thingiverse project that I made after breaking my rear cable clamp on my well used and beloved Valve Index: https://www.thingiverse.com/thing:4424259 Unfortunately that cable clamp, even while being more stable then the...

General:Designed this cable clip replacement for my Valve Index after the original one broke.It should be an easy replacement, as it was designed after the original clip.If it doesn't fit perfectly or you have tolerance problems with your printer,...

Valve index breakaway cable management you can mount on your desk using double sided tape, there are 2 versions, for on top of your desk and below your desk. To mount I've used double sided 3M tape. Te keep the connector in place in the casing you've...

The first thing that went wrong with my much-loved and frequently used Valve Index VR headset was the rear cable clip. Next was the upper pin that holds the cable in place, followed by the cable itself (pixel snow, occasional cracking sounds,...

This is a remake of my old Thingiverse project that I made after breaking my Front cable attachment on my well used and beloved Valve Index. https://www.thingiverse.com/thing:4424259 Unfortunately those front clamp, even while being more stable...