valve index mount 3d models

Remix with a cut along the slot to allow using any generic cable without fitment in the cable hole etc. Made so you can use any cable, plug it into the controller and just slide into the stand. All edges have been beveled (90º Edges are sharp,...

Comes with 2 models. ...The base one is 20mm thick for a shorter amount of cable and a 30mm one if you need more room.

I used two 40x40x10mm fan for cooling and a slide switch. ... You can adjust it to the position in the screenshot to print（The bottom surface is completely flat） Adjust the support frame according to your printer

My first attempt at a remix of two files. It will complain about not being airtight but it will Print. https://www.thingiverse.com/tootsypoopster/designs was the source of the grip and the rest comes from ...

Inspired by: https://www.thingiverse.com/thing:4568135 I wanted a cable strain relief that was both soft and durable for my comfort and the safety of the cable. So here it is. MUST BE PRINTED IN TPU or other flexible filament! Will need...

I have successfully rebuilt and divided the Wallmount to enable printing on even smaller printbeds. Additionally, significantly less Support Material is now required, making the process more efficient. The design has been optimized for seamless...

I was experiencing an issue where my ear speakers were quite loose, so I put together a quick o-ring based on a reddit thread's idea to increase the friction with an o-ring.ID: 9.6mmOD: 13mmheight: 1mmflat square o-ring type

Remix of https://www.thingiverse.com/thing:4598916 Just added some touch ups to the previous model. 1. Enlarged and repositioned the holes for the censors to avoid any tracking issues. 2. Cut away some of the material on the bumper and...

Feed the cable into the hider from the outer perimeter circling inwards. ...You can use the thicker version if you have more cable to hide.

This is just a remix as i had magnetic Cables for my controllers. and only one of the parts was able to be put on and removed with them on. ...so now i made a adjustment to the second part so both can now be taken off easily when Walking out of The...

Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956

My cables kept either misaligning or when I pulled the controller off the stand it would pull the cable with it. So I created these that slot in and push the USB plug so that it stays upright, and has a channel for a cable tie to go through, to hold...

I preferred the initial design, which came from BearCubsTeacher, but unfortunately, it wasn't compatible with the round magnetic connectors I had on hand. ...Therefore, I made adjustments to the holes in the base to accommodate my specific cable needs.

This is a work in progress and a temporary solution. Please let me know how to do it correctly. I grabbed the model and duplicated it three times, moving each copy down 0.5mm from the previous one. This STL file will likely have many defects if you...

Print Settings:\r\nFor optimal results, consider employing a minimum of 20% infill to enhance structural integrity.\r\nA layer height of 0.2mm paired with 30% gyroid infill yielded satisfactory outcomes for this particular print job.

This remix increses the size of the hooks, to make the clamp fit better when printed on lower-end printers. Remixed from: https://www.thingiverse.com/thing:4908421 Category: Video Games

Some RipOffGuards for the connectorpart of the cable :)inkc. ...one remix for a australian dude here on thingiverse.

Hi I am Frezzy from Vnvisual studio.

Hi I am Frezzy from Vnvisual studio.

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

I like the magnetic stand! They were a little unstable for me, so put cups on the top and tied them together to give a wide base and keep them together. Like the original, this fits with LAMA 90° magnetic data cable, USB Type C. Since I am in the...

I didn't make this. ...Feilen over at the VRCfacetracking discord is the mastermind behind this creation.

This is a mounting bracket for a Meanwell LRS-350, it requires: - 2x M3 nuts - 4x M4x4mm machine screws - 2x M3x6mm machine screws

This is a mounting bracket for a Meanwell LRS-350, it requires: - 2x M3 nuts - 4x M4x4mm machine screws - 2x M3x6mm machine screws

An easy way to mount your valve to a flat surface of your choice. ...It clicks easily in and fits keeps your valve safe on the designated spot.

A 40mm ball valve is accompanied by a valve mount, providing an efficient and reliable solution for controlling fluid flow in various applications. ...The combination ensures easy installation and operation while maintaining a secure hold on the valve.

mount for 4mm pneumatic valve If you like please help me to design more http://paypal.me/IfrahOmri thanks!

This mounting bracket secures standard-issue valves supplied with KingTech K-series turbos for remote-controlled airplane engines, accommodating 4mm fuel lines specifically. ...Although it should function with other valve types, a snug fit may hinder...

A 1/4" NPT five-way direct-mount Namur solenoid valve is denoted as Max-Air PN: SV61, and it boasts a NEMA 4/4X rating.