valve index stock 3d models

ImportantPlease try the cables before printing. Display Port can be finicky and an extension cable might not work for your setup. ...For me only a very short cable of 2 meters worked.Required Hardware4 wood screws 3.5x16 for mounting on the desk (don't...

Just a simple remix. Did not like the gab that was in there (caused unneeded support). Made it a little thinner to decrease built time and overall bulk coming from the holder -- moved the center of gravity to be more near the wall. I used simple...

Human: Modeled from scratch with precision and care, this 3D printed accessory was created using Fusion 360 software. Printed with a minimum of four perimeters and carefully oriented as shown in the model view, it boasts exceptional rigidity. The one...

Hi I am Frezzy from Vnvisual studio. This high-quality, photo-real model is designed to elevate detail and realism in any rendering project. The fully textured, detailed design allows for close-up renders and was originally modeled in 3ds Max 2012...

Printed, but never mounted.

I wanted to create this because for me it was annoying to stop/pause the printing to change the filament (color) for the middlepart if you want multicolored. Easy to print (30-40min) in any color you wish. ...simple to install - glue it, done!

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

Hi I am Frezzy from Vnvisual studio.

Can be mounted to a back plate with #6 wood screws, or directly to your wall with [medium Command strips](https://www.command.com/3M/en_US/command/products/~/Command-Medium-Picture-Hanging-Strips/?N=5924736+3294529207+3294774739&rt=rud).

The only component that has been thoroughly tested is the controller stand. The HMD hook, however, remains unprinted and untested, though it's expected to fit properly. ... Update March 31, 2020, 10:00 PM I've made some minor adjustments to the rear...

An exotic stand for exotic controllers; This organic concept leverages the natural center of gravity of the knuckles to cradle them in a stable orientation with a minimalistic design. <b>Warning</b>: Hanging the knuckles on the stand is...

My strap release button broke and I was out of warranty, so i remade it, using the top half from the official CAD model and the bottom half as an approximation from the pieces I could find. If you've lost the original springs, you gotta find some...

I made this cable guide to route the cable better when using an overhead cable management system and to allow the cable to flex over a longer section to reduce pinching. The tolerances are pretty tight so you may need to slice open the gap where...

Note: The v2 files have more forgiving dimensions for the cable pass through channel. I've modified my original design (https://www.thingiverse.com/thing:3886099) for those who are looking for something a little different. There is nothing wrong...

You will have to glue the logo in if it isn't too tight. You might need to also sand the logo for it to fit. My tolerances aren't perfect yet :( Once printed you should probably put some adhesive craft foam or something to keep your headset from...

Using a ceiling cable management system can be super helpful, but be aware that the clamp can technically be installed almost anywhere. ... It snaps into place very securely, making it a tad challenging to take out without causing some damage.

You'll have to attach the logo carefully if it's not a snug fit. It might be necessary to smooth out the logo with some sanding for it to sit properly within my tolerances. My precision isn't quite there yet. Once printed, you should apply some...

M4 nuts are required.Might not be a good location for some people.

They sit perfectly in the groves, I made it for you guys :)

Credit is due to Thingiverse for making available at https://www.thingiverse.com/thing:3772599 and also for the model located at https://www.thingiverse.com/thing:4270682

... and need a taller paddle you can just mirror it. Extra bits 6 #8x3/4" pan head screws 2 - 1/4" x 3/4" bolts with nuts and 1" washers Zip tie and some sort of sling 11-9 Added q2 cups and Index cups with cuts that some of my team has been using.

Discontinued magnetic gunstock I made, requires ~ 22mmouter 19mm inner diameter piping, an assortment of m3, m4, m5 screws + nuts, and some magnets. ... (thumbnail is of an older version)

Detailed 3D model replica of Valve Index VR headset with controllers and sensors

Updated 24 FEB 2020 This contains only the parts needed to use the Valve Index with the excellent NoobTube gun stock created by Toposolitario: * Right controller grip and clamp * Grip (v2.0) allows Index with handle booster to fit * Grip (v.2.1)...

A spacer that increases the height of the USB C connector on the charging cable that came with the Valve Index Controllers so you can plug it in by just putting the controller in.

A ball-joint mount for the HTC vive or valve index lighthouses designed to go in a room corner on picture rails. ... Printed in PLA on standard settings although I'm sure other settings will work.

Once piece slot style mount for valve index base station 2.0's. these let you use command strips or some other form of adhesive mount for the base stations as apposed to screws. I recommend you print these vertically slot up. ...snug fit and allows...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine out...

Charging cable adapter fix for this model https://www.thingiverse.com/thing:3751848 The original charging cables from the Valve index are to deep and loose. I tried out an other version somebody made, but it doesn't worked. This one should be...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine...