vic 20 power supply 3d models
314530 3d models found related to vic 20 power supply.thingiverse
Power supply case and instructions. Also on https://github.com/Jaystonian/PowerSupplies Print bottom with internal side facing down, with supports. Print top with switch side facing down (rotate 45), with no supports. ...
thingiverse
To build the power adapter you need these things: 1 transformer FL PCB 24VA 2x9V (FL 24/9) 1 tumbler switch 250 V (Tru Components TC-R13-112LP-02 LED) 1 Hama Euro power cord (2 wires) for the power cord (primary), we use half of the cable for the...
thingiverse
The 9VAC from the original C64/VIC-20 CR power supply are not sufficient. Please read the documentation file (*.docx). ... If you want to know more about this project: http://tech.guitarsite.de/vic20_power_plug.html If you want to know more about cable...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=60392 Instructions Remixed to fit over 20 amp power supply. The holes allow for a flat power cord and round output cord to be attached without additional hardware. I use two zip ties to keep...
thingiverse
This Thing is a power supply mount for any printer that used 20-2020 extrusion for a frame. It was designed specifically for a Flsun Delta Kossel but it should work for others as well. The Flsun Delta comes with a very generic power supply that...
thingiverse
This is a remix to fit over a 20 Amp power supply. The wires are run directly without the need for a power plug. Customized version of http://www.thingiverse.com/thing:60392 Created with Customizer!
thingiverse
Simple 2 two prong housing for the non-standard Vic-20 power plug. By no means perfect as I'm new to this, but worked out well for me so here it is. Feel free to copy/remix/fix/etc. For the electrical part of the connector, I believe this is...
thingiverse
Although the VIC-20 was not as famous as its younger brother (the C-64), it did give the world the Famous Commodore Breadbin case, so there's that. Fairly simple build - print in colors to match the photos, and then apply stickers - one gotcha is...
thingiverse
Holder for Commodore VIC-20 cartridges. Simple design with relatively quick print time compared to other similar ones. ... Printing: Nothing special, no supports needed, use your favorite settings.
thingiverse
Replacement hook tabs for the VIC-20 case, to replace the brittle originals. ...The case is notoriously difficult to open and close without breaking them off, and this solution makes it easier.
thingiverse
...No guesswork. Just print them out, align to the notch and clue them in place. I have a detailed article here: https://www.thegeekpub.com/237121/commodore-vic-20-clip-repair-3d-printed/ and a YouTube video: https://www.youtube.com/watch?v=e00pJapGMAU
thingiverse
I recently found a Commodore VIC-20 (Made in Canada 1984) at an Estate sale however the £ key was broken off. ... All the models I found were not for this keyboard revision so I modeled a replacement that worked and thought I would share it.
thingiverse
This is a mounting bracket for mounting a COR-20 power supply to a wall.
thingiverse
This is a wall-mount for the Vic-20 and the earliest Commodore 64 models that used the slightly fatter case. I simply took the design that this was remixed from and stretched out the front half of the hook a few millimeters and that made it fit very...
thingiverse
Work-in-progress modification of my earlier VIC-20 cartridge model (http://www.thingiverse.com/thing:69261), to be able to hold at least a DIN connector (http://www.thingiverse.com/thing:104160) in the back. Will upload the openscad code once it's...
thingiverse
I dedicate it to one of my heroes, Elon Musk, who learned to program on a VIC-20. Thanks to Jim Brain for the original cartridge, and to Ismail, Olga and Niels for helping me print the label. ...
thingiverse
Simple mounting bracket for 150 Watt LED power supply to 80/20 10 or 15 Series extrusions. Uses 1/4 Mounting Screws. ... LED Power Supply - http://www.amazon.com/dp/B00IHZ9ME0/
thingiverse
A mounting case for a power supply, can be used with some 20 & 30 amp PSU's out there. Measure before you print, some power supplies are larger and some are smaller. ...You should be able to scale this to fit your needs.
thingiverse
Parts list: DC DC Buck Boost Converter: https://www.aliexpress.com/item/4000424191711.html?spm=a2g0s.9042311.0.0.27424c4dp6dwng 14€ 10Pcs 3A 12v For DC Power Supply Jack:...
thingiverse
This is a stand for 5 VIC-20 cartridges. ...There is a little fan art logo on the front.
thingiverse
VIC-20 Cartridge Remixed for easier printing. Removed indentation for sticker so it can be printed flat, reinforced tabs to reduce likelihood of them snapping. I print them without support. ... Rest of stuff needed to make your own cart can be seen...
thingiverse
This is a set of panels I made for a Commodore VIC-20 which I wanted to convert to house a Raspberry Pi. For the panels; when one holds hold a cable or something else, I have also included a blank panel. The Autodesk 123Design file is included as...
thingiverse
I have some commodore VIC 20 cartridges in my retro collection so I decided to organize them. These designs are meant to be used with a standard photo box. Due to the size of my printer these were designed to be fit together so print 2x to get a...
thingiverse
This is a cartridge guide for the Commodore VIC-20 and (probably more important) for the VickyTwenty (modern replica board). The cartridge guise is something to miss, when you don't have it. It guides the cartridge into the cartridge connector...
thingiverse
The Commodore VIC 20 has a plastic outer case that splits into a top and bottom half. The rear of the top half has tiny fragile pins that slot into to lower half to hinge the case together. I'm told many of the Commodore 64 cases are the same. ...
thingiverse
... color, then glue them. then use double sided tape to attach it looks alright. Let me know what you think edit: if you dont have a 3d printer you can buy one at my store https://www.etsy.com/kenji3d/listing/772597606/commodore-vic-20-label
thingiverse
... I used a screw about the same diameter and 10mm long. Once you're done, do your usual wrestle with the back of your Vic-20 to get the cart in (hence why you should do a good job gluing the board stop), and enjoy the marvels of vintage computing.
grabcad
Sheet metal model of a computer power supply source
thingiverse
Anet logo version of 20 amp supply cover. More details found here. https://www.thingiverse.com/thing:2524688 Picture posted of supply it's intended for. ...Notable features of this supply are the cover screw to the left and case metal extending down to...