vintage zenith radio knobs 3d models
58907 3d models found related to vintage zenith radio knobs.thingiverse
Vintage radio knob, I copied the design from photos original knobs.
thingiverse
... to my 1965 Chevrolet Corvair. ...They will likely fit other mid-60's GM vehicles as well. I am installing an old Motorola radio to replace the Delco, but the knobs are different, so I decided to make these in order to retain original appearance.
thingiverse
I suggest using M3 nuts, you can file sides a little bit to fit them into a rectangular slot. Other knobs Check out my profile for other knobs if you are interested in restoring vintage radios. I have also other knobs and radio projects on my...
thingiverse
Replica of Garod console knob My floor console made by Garod was missing one knob so I have modeled it, it was probably used in other radios. Check out my profile for other knobs or my website (SP6GK.com) if you are interested in tube radios. ...</p> ...
cgtrader
Vintage,Pre-War,Zenith Radio.Model: 12-S-267 Ch=1204 - Zenith Radio Corp.; Chicago.Years 1936-1945. sizes 27.7 x 43 x 15.2 inch / 704 x 1092 x 386 mm. ...Textures 4096*4096 PNG
cgtrader
Detailed model of a vintage Zenith 812 radio. Itâs classic style is ideal for many type of interior scenes. The model is properly UV mapped and textured (diffuse, normal and specularity). Ready for quality renders and close ups. Renders were...
thingiverse
I needed two knobs for a car radio so I modeled some in fusion 360 and 3d printed them. They work perfectly. You can see the process and outcome on my youtube channel. How to Design and 3D Print new Radio Knobs using Fusion 360. ... ...
cults3d
Vintage radio knob universal Vintage radio knob Vintage radio knob old equipment before printing take measure of the diameter of the pin so you can set the hole of the knob Very easy to print!
thingiverse
Vintage radio knobs. 3/4" - 1" - 1-1/2" - 2" 1/4" shaft and set screw holes ready to tap 8-32. ...
thingiverse
Vintage car radio knob. Fits Becker Europa. May fit others. Original knob has a steel split sleeve to provide compression. This design uses a zig-zag pattern to provide compression. Not as strong as the original. But, it is functional. ...
thingiverse
Vintage radio and volume knob. Comes in three flavors, 24, 30, and (updated) 27 mm diameter (all for 6 mm potentiometer shafts). Print in PLA with 0.1-0.15 mm layer height (the smaller, the better and rather slow) to get a smooth surface at the...
thingiverse
Vintage radio knob, I copied the design from one of the original intact knobs. It is friction fit onto the shaft of a potentiometer, volume in this case. I printed my first one in red filament just to have a bit more contrast, i'm quite pleased to...
thingiverse
This is a replica of the radio knobs found on a vintage french radio. The original knob was molded, probably Bakelite[TM]. As knobs were damaged, I redesigned the knob in OpenSCAD in a few minutes. To be fully functional, a set screw shaft collar...
thingiverse
I've made this to replace missing power knob on Philco 77. ...It fits most of other radio models from that period. ...you can use it as volume, dial etc button as well.
thingiverse
My wife needed a new knob for her replica radio, so I made one. ...HInt: its the black one ;) Print Settings Printer Brand: Prusa Printer: ...
thingiverse
While renovating my 1937 Philco radio, I could not find any knob replacements. I created these and they look pretty good. I have the radio project on YouTube if you'd like to see the build. ... https://www.youtube.com/watch?v=jcpF9YZYJf4
thingiverse
This is a second attempt at making a generic replacement radio knob for a 1/4" shaft. I marked this as a work-in-progress because I need to finalize the specs for output in terms of dimensions. It should be right around 25mm, I think. ... As you can...
thingiverse
Created as a replacement for a knob on an old valve radio (the restoration of which unfortunately hasn't got beyond this point), this solid knob is designed to fit potentiometers with 6.3mm "D" type (flattened side) shafts. This is probably the most...
cults3d
It's cute vintage radio model. ... Listen to music together 🎧 >>> https://youtu.be/jUYF-hNcTIA
thingiverse
A 3D vintage radio design. This is my first 3D printed project and submission to Thingiverse. ...Enjoy!
sketchfab
I thought I’d go and model a few vintage radios, the first being the Motorola 53H. ...There’s a bit of charm when it comes to vintage objects.
sketchfab
Vintage Radio. Game Ready. Radio is the technology of signaling or communicating using radio waves. Radio waves are electromagnetic waves of frequency between 30 hertz (Hz) and 300 gigahertz (GHz). They are generated by an electronic device called a...
sketchfab
An old radio based on Telefunken 50’s radios, the brand name and logo are from a fake company to avoid copyright infringement. It’s intended to be used as a static object for games with realistic graphics. For sale on Artstation Marketplace!