vive cable 3d models

This is an anchor for the Newer HTC Vive cable (Single Cable)

These files are a remix of the vive cable clip by RichWP. on the belt clip I added a hook for both sides to make it a bit more secure. other then that it has no change. I have included the cable holder with no change just so you don't have to go find...

A Box to make sure the cables of the HTC-Vive dont come loose during usage.

A Box to make sure the cables of the HTC-Vive dont come loose during usage.

Works with v2 cable (Single). ...Allows you to anchor cable to desk or wall.

I printed a wall mount cable holder for my oculus rift. I used a skipass holder as a retraction tool. ...Hope you like it

A top routed Vive cable mount with strain relief. The base slides onto the top of the Deluxe Audio Strap and uses 4 brass M3 inserts pressed into the base to secure the top. ... Uses these as strain relief --> http://a.co/7Vgk7k8 If you don't want to...

Customized version of http://www.thingiverse.com/thing:363800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=363800

case to fix HTC Vive cable-box under table

If you have a suspension system for the Vive such as the Hyperkin Freestep or the kiwi VR cable management system, this clip can stop the cable from sliding through the Carabiner and into your play space. Couldn't find one so I made one that...

I made this to work in conjunction with the Jackson Safety 370 headgear adapter found here http://www.thingiverse.com/thing:1639795 You will need to print out the cable holder portion from this belt clip. http://www.thingiverse.com/thing:1574006...

Just a simple guide for the lighthouse cables of the HTC Vive. I just sticked them with double sided sticky tape to the wall to route the cables. ...Works just fine.

I wanted to arrange all front cables used by TPCAST on my vive. Now they are all alligned and do fit perfect. Also no further risk of connection lost. I do recommend to clip cables in following sequence: first the thickest cable (HDMI), than follow...

Full write-up: https://hackaday.io/project/163470-vive-lighthouse-sync-cable-reel

I was sick of losing the charge cables for my vive controllers in the rat's nest behind my computer. ... Rather than clean up the mess, I made this!

I got tired of having the headset sitting on my desk, but the only mounts/hangers I could find took a long time to print and had no place to store the cable as well, so I made this! Note: I take no responsibility for any damage to your wall,...

Finishing off my Frankenquest, I wanted the ability to tidy up my USB and Link cables against the Deluxe Audio Strap without any more velcro.  Whipped up these easy snap on clips.  They'll let me put multiple cables in place when I'm switching...

... up these easy snap on clips. They'll let me put multiple cables in place when I'm switching between charge and link, and tidy the charge cable away when I'm just using the battery for the counterweight, and take no time to get cables in and out.

They'll let me put multiple cables in place when I'm switching between charge and link, and tidy the charge cable away when I'm just using the battery for the counterweight, and take no time to get cables in and out. Print Settings Printer Brand:...

I designed this to use in combination with: https://www.amazon.com/Skywin-Management-HTC-Virtual-Reality-Headset/dp/B0733NN7G8/ref=sr_1_4?ie=UTF8&qid=1514558155&sr=8-4&keywords=htc+vive+cable to keep the cable not sliding over the carabiners

This is just a basic cable clip to go on the back of most soft back chairs to stop the htc vive cable from sliding down the sides of the seat while in seated VR. ... works really well, and does not need glue or screws to hold itself in place, just...

This is an overhead cable management system for the HTC vive. I bought the track at home depot and the leashes from amazon. ... Track: http://www.homedepot.com/p/Everbilt-24-in-Bi-Fold-Door-Hardware-Set-18399/202034318 Leashes:...

A simple thing I designed so I could keep the charger cable off of the floor. It fits the ~19 mm ( or 0.755" in freedom units) diameter of the tripod I use. I ended up not using the small 'wings' since the fit was snug enough. But I doubt they...

A simple thing I designed so I could keep the charger cable off of the floor. It fits the ~19 mm ( or 0.755" in freedom units) diameter of the tripod I use. I ended up not using the small 'wings' since the fit was snug enough. But I doubt they...

A small clip that slides on the top strap of the HTC Vive Deluxe Audio Headstrap. ... It can be used with a small zip-tie to attach the HMD cable Prevents slipping and tangling of the cable, especially with overhead cable managment.

Made these to hold my optical Oculus link cable to my HTC Vive focus 3 Headset to avoid pulling the cable out and damaging the socket. I printed two sets for security and they simply clip on and off as needed. See Photo. Printed with no brims...

I realised that Thingiverse is empty of parts for the new HTC Vive COSMOS, so I designed with the help of @METROPHADES some support for the HMD and the cable. This is a modification of the support for the HMD that I made but with a place to hold de...

You will likely need to rotate this onto it's front before you print it.

3 Line version of the Vive Delux Audio Strap Cable Clip I made. This was done by request. I don't actually own the 3 Line cable so I have no was to test this. ... Print at your own risk.

Based on the remix by Quintesse, I added a hanger to put the coiled headset cable on, additionally I wasn't 100% confident that the headset might never work itself out, so I added a locking bar across the opening. Probably would have been better to...