vive stock 3d models
40647 3d models found related to vive stock.thingiverse
After printing different Vive Stocks I decided to create an own one which works. It can be used with 10x5 mm magnets. The magnets can be put from the backside into the mount, so if you use strong magnets it doesnt matter because they cant move out. ... ...
cults3d
After printing different Vive Stocks I decided to create an own one which works. It can be used with 10x5 mm magnets. The magnets can be put from the backside into the mount, so if you use strong magnets it doesnt matter because they cant move out. I...
thingiverse
This is a revision of Vive Stock by hapteck, published Mar 26, 2017 of the top piece that is on the Vive controller and the mount for the rail for magnet. it seems that the original is made for .75" magnets and the magnets listed are 1"(1002304). I...
thingiverse
This is an updated and remixed version of Croccy22's Vive Stock. I slimmed it down and made more holes for stability. Really works well for VR games that require shooting long distances and also helps add immersion. Feel free to ask me any questions....
thingiverse
Constructed my own design for the stock of the vive rifle controller. It should just barely fit a 200mm print bed. Use supports for the tab part. I also included a shorter stock attachment to help to be able to aim down the sights. The alternative...
thingiverse
... to Croccy22, I just modified one part to make a smaller piece all together for my liking. ... An updated version of this stock is located at http://www.thingiverse.com/thing:1744932 Print Settings Rafts: No Supports: Doesn't Matter Resolution: .4mm
thingiverse
Not a derivative but directly connected to it. ... Why would you have a pair of stock Vive lens if you didn't swap them out right? Quick case to protect your stock lens once done. ... Print time: ~40min for a set at 0.2mm 20%.
thingiverse
This is a gun stuck you can slip onto the end of a HTC Vive controller for a more real gun feel in VR games. ...You should be able print as is, but you may need to change it's orientation depending on the size of your printer.
thingiverse
Vive Gun Stock with quick release 15mm magnets, print on lowest settings in 1 hr.
thingiverse
I couldn't find a Vive stock that I liked so I mixed the best two I could find. I utilized the front controller from this http://www.thingiverse.com/thing:1828084 design to put the mote in the correct orientation for onward. I used the weaver rails,...
thingiverse
Shoulder stock intended to be used with the Rifle Controller for HTC Vive. ...Connects to the stock attachment part using the customized bolts and nuts (http://www.thingiverse.com/thing:1696645) Print Settings Printer Brand: MakerGear Printer: M2 Rafts:...
thingiverse
New version of my Vive gun stock with attachment by a cup instead of a clip. ... * Adjustable height range of 3 3/4 inch (95 mm) * Adjustable length of pull from 12 inch to 15 inch (305mm to 381mm) * 100% printed construction, no fasteners or glue...
prusaprinters
New version of my Vive gun stock with attachment by a cup instead of a clip. Adjustable height range of 3 3/4 inch (95 mm) Adjustable length of pull from 12 inch to 15 inch (305mm to 381mm) 100% printed construction, no fasteners or glue needed...
thingiverse
Currently testing a stronger folding stock arm - V2-Reinforced-Folding-Stock-Arm.stl The hardware required for this build is: 6 m3 nuts 2 m3 nyloc nuts 4 m3 20mm screws 2 m3 12mm screws a section of 1 1/8th wooden dowel from the homeless despot an...
thingiverse
I made a different stock to work off a horizontal rail so I could get my headset closer to the stock without touching. ...I also printed an extra Stock - A and an extra Rail to make it look like the picture.
thingiverse
... front. 12/6/2017 updated the middle piece to be ambidextrous. Things you need one #8x3/4 bolt and nut two #6x1/2 wood screws Sling is nice would recommend a one point hooked between the back mote and stock connector. ...I use a bit of para cord.
thingiverse
A simple gun stock for HTC Vive, made in 2 pieces, the front-stock and back-stock. This way you can easily reload, go one handed etc. without fiddling with a stock hanging in a belt. The two pieces are assembled with a male and female plug,...
thingiverse
Vitamins for stock 6 - #8x3/4 or so wood screws 2 - 1/4 x 1 1/2 shoulder bolts with nuts 2 - 1/4 x 3/4 bolts with nuts 2 - Springs that will fit over the 1/4 shoulder bolts but not the nuts. They should be lose coil springs to allow enough room in...
prusaprinters
<p>A case to hold the lenses cases from M600</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Ender 3</p></div> <p><strong>Rafts:</strong></p>...
thingiverse
Controllers are held into the craddle. Should also lightly snap. Compatible with controller covers. Use 6-32 screws for locking. pipe used: 1-1/4" PVC sch 40 Note: tolerance stack may require you to sand down the part for it to slide on the...
thingiverse
With this design it should be easier to attach your controllers to the stock while wearing the Vive, as there is no way to attach the controller in the wrong orientation. ...The newly added legs should guide the controller in to the correct placement,...
thingiverse
Want to have a place for your stock rather than just toss it around when you're not using it? I know I did. Made for #6 wood screws. You'll want to get some 1-1.5" in length. You can also get by with some command strips if you don't want to put...
thingiverse
Raider cs35 cross Canon Longstrike cs6 Left controller easy remove
thingiverse
I was playing a nice round of H3 on my vive when I examined my M4 and saw that you could adjust its stock and I had a realization, what if you had a controller stock that you could put an AR stock on to have it be comfortable AND adjustable? So I...
thingiverse
Let the glue dry/cure fully - neodymium magnets are quite strong, and we don't want them to pop out mid-game And please refer to the photo of assembled stock for reference on how the pieces come to life together :) Note that there's one "Rail" piece...
thingiverse
Parts to print: - 2 copies (one for each controller): Controller - bottom - 2 copies (one for each controller): Controller - top - select the variant for your magnet size - 2 copies (one for each controller): Controller - mount - select the variant...
thingiverse
Using: Raider cs35 cross Canon Longstrike cs6 Left controller easy removable Different mods possible
thingiverse
I modified the original design to fit two 18mm x 3mm disc magnets from the Home Depot. ...Make sure to use opposite polarity on one of them, so you can't put the controller in wrong.