vm275t 3d models
56 3d models found related to vm275t.thingiverse
Camera mount for the AIO VM275T Micro Camera. I've included a 15 degree angle version. ...Use double sided tape to install on the frame.
cults3d
Lens cap for VM275T mini camera (https://hobbyking.com/en_us/vm275t-5-8ghz-25mw-48ch-ntsc-pal-mini-vtx-600tvl-fpv-camera-micro-fpv-whip-antenna.html) If it is too tight or too loose to fit, try using the "scaling" function of your slicer to adjust.
thingiverse
Lens cap for VM275T mini camera (https://hobbyking.com/en_us/vm275t-5-8ghz-25mw-48ch-ntsc-pal-mini-vtx-600tvl-fpv-camera-micro-fpv-whip-antenna.html) If it is too tight or too loose to fit, try using the "scaling" function of your slicer to adjust.
thingiverse
I designed this to mount the popular vm275t camera that typically comes with the vtx and camera combined. It can only be used after the camera has been separated. This allows you to use the vm275t with any tiny whoop canopy but does not require one.
thingiverse
This is a case for the Hobbyking VM275T fpv Camera. it hold it and protects it. you can also use it as a mount as it is easy to remove the Camera. Print Settings Printer: Folgertech FT-5 ...
thingiverse
This is a mount for the VM275T camera, designed for the hoverbot vibe: https://hoverbot.io/products/hoverbot-vibe
thingiverse
Camera mounts for your Tinyshark to support the VM275t AIO camera or the Micro CMOS camera. Mounts bolt into the stack and take the place of a single M2 nut under your ESC. ... Shinehalo AIO: http://amzn.to/2HOfmCO VM275t AIO: http://amzn.to/2FAqClJ
thingiverse
VM275T Camera Mounts for the DJ105: http://www.thingiverse.com/thing:1580385 I printed it in Taulman's Alloy 910. ... There is a 0, 10, and 20 degree mount.
thingiverse
This is a super minimal Tiny Whoop mount for the VM275T AIO camera! I designed this to cut as much weight as possible from my Whoop. The angle is 13 degrees, which I found to be nice! Print Settings Notes: This is intended...
thingiverse
This is a protective camera case which can be used to protect almost any of the small all-in-one (AIO) camera/VTX units such as the VM275T and its variants. The camera case uses 2mm bolts to attach to the mounting plate/bracket. While designed to...
thingiverse
This is a modified 4 point camera mount system made for the VM275t FPV micro camera and the cockroach frame, or any other "tiny Whoop" size quad. I wanted a 4 point mount dew to the FC always getting un-clipped, ruining the flight performance, and...
thingiverse
This is a camera mount designed for the HoverBot Nano. ...More info at hoverbot.io
thingiverse
print parts insert camera glue back on with small amount of super glue 2x M3 screws to fit mount bracket in place
thingiverse
Case for Hobbyking VM275T or Banggood CM275T FPV Camera. ...Mounting holes are setup for 20mm x 20mm.
thingiverse
This is a camera mount for the super compact camera + vtx vombo VM275T. It has a 10deg camera tilt. Right now, the initial concept is 0,66g. I have now the 0.43g lightweight version that is also snug fit. I just wanted people to test fit. In my print...
thingiverse
This is a simple mount for a VM275T FPV camera & transmitter all-in-one unit. It is designed to be easily transferable between RC models and to leave the camera as open as possible to help keep it cool. Rubber bands can be looped around the mount to...
thingiverse
Modded this cam mount https://www.thingiverse.com/thing:1972479 Camera lens in center and add hole for power wire on back Design for this camera: https://goo.gl/N6VTMA
thingiverse
This has been printed on a MarkForged MK2, in Nylon. ...You will need a precise printer to make this work.
grabcad
We think so and so will you when you lay hands on one!Weighing in at a mind-blowing 3.4g and measuring less than 15mm in any direction (not including antenna) it's hard to imagine any model that this little beauty won't fit into with ease.Don't...
thingiverse
I designed this mount for the Crazypony AIO micro camera and VTX combo to be used on a Blade Inductrix or Eachine E010 frame. Print Settings Printer: Prusa i3 ...
thingiverse
Camera mount for tiny whoop - should work for most micro AIO cameras. ... I designed this in order to protect the antenna header/connector I secure the camera with a blob of hot glue between the holder and the lens weight is around 1g
thingiverse
Hallo! Just another camera holder for the micro drone eachine e010/jjrc H36, but with simple Head Up Display for low battery alert! A simple telemetry emulation! Place it removing canopy, unscrew the front screw place the camera holder and fix...
thingiverse
Flexible TPU mount for VM275T camera onto the Blade Inductrix
thingiverse
Designed for especialy "vm275t v1.1" aio fpv camera This design also protect antenna little bit.
thingiverse
Flexible TPU mount for VM275T camera onto the FlexRC Nano-X (16mm stack)
thingiverse
This is an camera holder for the ZMR250 frame. ...The camera is the VM275T from Hobbyking. ...
cults3d
Designed for especialy "vm275t v1.1" aio fpv camera This design also protect antenna little bit.
thingiverse
I needed a mount for my VM275T AIO Camera/VTX on the iFlight iX2. ... Remixed from thing:2303204 & thing:2626996 (Printed in ABS, as the VM275T when powered is hot enough to make PLA soften)
thingiverse
###TINY WHOOP FPV cam mount | Kamera Befestigung For 'EachineTX04' or 'VM275T' FPV cam Mounting holes | Befestigungslöcher: 36,5mm