vortex 150 3d models
23843 3d models found related to vortex 150.pinshape
Just a simple ImmersionRC Vortex 150 Plate/Bumper Print Settings Printer: Dremel 3D20 Rafts: No Supports: No Resolution: 0.1 Infill: 35%
thingiverse
This is a part for the Vortex 150 since its hard to get your hands on the crash kits in other colours than black and red, with this creation you can print it however you want.
thingiverse
Loc8tor case & adapter to perfect fit in Vortex 150 nini drone, this case fits the loc8tor coin and fits in the arm holes usin two long screws, one side lowered so as not to interfere with pad, hollow up to put loc8tor area with mini bepper up and...
thingiverse
This cover is for a Vortex 150 / 180 To install a dvr on the vortex at minimum cost using original camera It uses the Rumcam DVR https://www.getfpv.com/runcam-mini-fpv-dvr.html https://shop.runcam.com/runcam-mini-fpv-dvr/ Fits on the Vortex without...
thingiverse
I needed a way to keep from damaging my Vortex 150 when transporting it in a duffle bag and as a method of storing it while being able to stack things on top of it. *Warning--- this box takes up almost a whole 200x200 bed so if possible print on...
myminifactory
Loc8tor case & adapter to perfect fit in Vortex 150 nini drone, this case fits the loc8tor coin and fits in the arm holes usin two long screws, one side lowered so as not to interfere with pad, hollow up to put loc8tor area with mini bepper up and...
thingiverse
FYI, The green unit is the Vortex 150 and the white is the Vortex 180. ... Manual - https://www.runcam.com/download/split4k/RC_Split_4k_Manual_EN.pdf RunCam - https://shop.runcam.com/runcam-split-4/ Camera available here ...
thingiverse
a flat skid for the vortex 150 quad Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: No Supports: No Resolution: .20 Infill: 90
thingiverse
This is a protective foot / slider for the immersion vortex 150. I think it will fit the 180 as well. ... I printed in PLA 100% infill.
thingiverse
I couldn't find any session mounts for the ImmersionRC Vortex 150/180, so I took what was already existing and remixed them together. This is V2 as V1 was scrapped since it too flimsy to support the session. I added a few reinforcements and have...
thingiverse
since I got the vortex 150 it became one of my favorite quads and I really wanted to record HD video from it and the runcam split was the only camera that I think it will work with out affecting the flight characteristics of the quad to much (CG) it...
thingiverse
This thing allows you to mount a runcam split to your ImmersionRC Vortex 150. It includes a mount for the actual camera module aswell as for the PCB Stack. Please note that all steps of the installation procedure need to be performed in a partucular...
thingiverse
After one bounce on concrete and chipping my carbon fiber skid plate and marring my screws, I knew I had to make this. I printed it at 80% infill with PETG, ABS would be more than fine I just had the stuff in the machine at the time. For me the parts...
thingiverse
printed in T-glass with 30% infill. fits a 850 4s battery well, separate straps for tying down the mount, the runcam, and the battery. ...very quick batt swaps 15degree cam angle hooks to hold battery cable out of the props
thingiverse
Version 1 with Antennae out back. ...V2 coming with Antennae out top.
thingiverse
this is only a test, will update once printed and checked for absolute fitment... ...check back soon!!!
thingiverse
remixed from IRC Vortex 180 Axii Mount by Porksoduh i added rx antenna tube holders V2 has thicker tube holders for slighty more rigid antennas. v1 tubes holders are fine but they bend a little too easy for me, concerned they will hit props if bent...
thingiverse
extra large vortex front rear bumper
grabcad
Vortex is a clean shaped papertowel holder for Umbra. It can be used either on the wall bothe vertical and horizontal. And it can be use independently in the table. It is made of 4 pieces in total. - a wallmount - a flat profile o-ring - a paper...
thingiverse
Customized version of http://www.thingiverse.com/thing:355889 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=355889 Instructions Using the following options: w1 = .4 L = 150 D = 58 R = 6.2 H = 100 Rspool = 15
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_bar_screw_nut_d = 6.01 gopro_bar_rod_d = 31 gopro_rod_nut_th = 3.6 gopro_captive_protruding_h = 0.5 gopro_bar_th...
thingiverse
This is the new firefly 150 it is inspired by the famous vortex 150. It is designed to deliver a unique flying experience in yet a so small form factor. If you like the design but don't want to build It is still a work in progress so bare with me if...