vortex 250 pro 3d models
83562 3d models found related to vortex 250 pro.thingiverse
... to one of your choice. I have printed this in PLA and at only 1mm thick it is very bendy but stiffens up quite nicely when all bolted together. I have used this with the Vortex 250 Pro Racing Kit, Bumpers and Pimp Kit and all fits together nicely.
thingiverse
This is my design of a Vortex 250 Pro compatible Gopro Hero 3 Housing. It should prevent the Gopro from scratches and damage during crashes. All buttons and LEDs are accessible only the screen and the wifi button is not available. But normally i...
thingiverse
This is a GoProSession mount with an 35° or 40° angle for the Vortex 250 Pro. Variations regarding the angle should be easy to make, so just leave a note. I printed this on the Ultimaker 2 And support set to "touching buildplate". But it shoud also...
thingiverse
Parti disegnate da me per riparare e rinforzare il Vortex 250 PRO
thingiverse
Replace damaged lens holder ring on ImmersionRC Vortex 250 pro drone. ...
thingiverse
Support Gopro Pour Vortex 250 Pro Print Settings Printer: Prusa i3 Hephestos Resolution: 0.2 Infill: 25
thingiverse
This is my design of a cam skid plate. ...It will protect the cam or your Vortex 250 Pro on landings in grass of somewhere else. Also in crashes :-) Please hit "like" if you like & download it. ...Thanks Stanley
thingiverse
Mobius holder 20° for Vortex 250 Pro Support Mobius 20° pour Vortex 250 Pro Vous pouvez découper un rectangle de 35mm x 19mm dans un pad d'accroche et le positionner dans son emplacement, ça évite que la caméra glisse vers l'avant ou l'arrière. ...Le...
thingiverse
This is the Vortex 250 Pro HS1177 camera mount. Mount the camera in the mount before installing it in the Vortex. Original standoffs can be used. Slide the cam into the mount from the rear, untill it snaps in place. Use the 2mm screws, coming with...
thingiverse
A camera protector for the Vortex. Original screws can be used. ...Print Settings Printer: Wanhao 3 Duplicator Rafts: ...
thingiverse
Vortex 250 pro side panel with antenna channel
thingiverse
I make this pin for the Vortex 250 pro but should work on any dumper
thingiverse
I've put all Vortex antenna rear mounts I made here in to one thing. - **V1** is rear mount just for RX antennas if you have receiver hidden inside the frame. Antenna holes are 3mm and you can use straws like coffee stirs, cotton bud straws. Can...
thingiverse
Support Gopro de 0° à 20° pour Vortex 250 Pro Va avec la protection Gopro session. ...http://www.thingiverse.com/thing:1350062 Print Settings Printer: Prusa i3 Hephestos ...
thingiverse
Mobius 20 degree mount for the ImmersionRC Vortex 250 Pro. ...Velco strap can be used in the first slot, the mount is held in the correct alignment by the platform's vibration dampers and FPV camera screw heads which stops it from moving sideways.
thingiverse
This is my Vortex 250 Pro GR-16 Bash Guard. I've made it to prevent the GR-16 from damage in a crash... :-) Check the dimensions if it suits for other receivers. Length= 47mm Width= 22mm Height= 15mm It is mounted with 2 to 4 2mm screws. Please hit...
thingiverse
... resulted in jello in the footage if it moved in flight. The new design moves the camera further forward and lower with a stop at the back and a cutout for onboard power adapters. Mount is not compatible with Vortex 285 only with the Vortex 250 Pro.
thingiverse
An updated RunCam2 camera mount for the vortex pro 250. The old design allowed the camera to slide to the back of the mount and touch the antenna. This resulted in jello in the footage if it moved in flight. ...The new design moves the camera further...
thingiverse
If like me you fly the Vortex in a sandy area, or you're tired of scooping dirty via the front camera hole, then this thing is for you :). It basically closes the front hole between then two front arms. What about cooling for the electronics/Vtx ? ...v2...
thingiverse
Remix top mount from https://www.thingiverse.com/thing:1597107 to hold gopro session. ...Print in flexible material only This mount is 20 degrees.
thingiverse
There are many antenna holders out there. This is my version of one. ...I used 3mm plastic tubes 50mm long.
thingiverse
I designed this mount to attach a Runcam 3 that was wearing this TPU sleeve https://www.thingiverse.com/thing:2306842 The mount uses one of the protective lens jut outs to lock the front into place. Then a velcro strap can be wrapped around the...
prusaprinters
<p>I designed this mount to attach a Runcam 3 that was wearing this TPU sleeve <a href="https://www.thingiverse.com/thing:2306842">https://www.thingiverse.com/thing:2306842</a></p> <p>The mount uses one of the protective lens jut outs to lock the...
cgtrader
... The bottom lugs have been spaced to sit perfectly on the outside of the ImmersionRC Vortex 250 Pro's GoPro Recliner to Prevent the Gopro from sliding left or right.3D PRINTING SETTINGSLayer Height: 0.20 Support Needed: Yes Infill: 100%
thingiverse
a mount for the go pro session & vortex 250 i havent got round to making one yet so let me no edited 01.08.15 alteration amended has been moved forward to allow room for antenna
thingiverse
I designed this wrench to lock the motor bell of Elite 2204 motors in place when changing props. I use the new v2 Gemfan 5050 3 blade props and they are too tight, I had to be able to lock the bell to be able to remove them, quite a PITA but with...
thingiverse
https://www.youtube.com/watch?v=H_YGm8vCmlY
thingiverse
This is an antenna mount designed to suit the Frsky D4R and X4R range of receivers. (however it can be used with any receiver that uses long antennas... Futaba/Lemon etc). I mount my X4Rsb in between the frames. The antennas push through the frame...