vortex 285 parts 3d models
553097 3d models found related to vortex 285 parts.thingiverse
These are parts for you Vortex 285. ...With these feet´s you protect your centerplate and it looks nic ;)
thingiverse
Mount for Futaba R2008SB receiver on a ImmersionRc Vortex 285. ...
thingiverse
Standard motor mount for Vortex 285, never was printed on 3D printer.
thingiverse
Vortex 285 Side Print Settings Printer: DaVinci JR Rafts: No Supports: Yes Resolution: 0,2 Infill: 30%
thingiverse
Found this file here and remixed it to fit the vortex 285 frame better and looks very cool!https://grabcad.com/library/3d-printed-flexible-cover-for-gopro-session-1 Print with flexible filament only and Enjoi! Print Settings Printer Brand: ...
thingiverse
Version 2 - 90 degree antenna mount to suit IRC Vortex 285 racing quad. This one has been beefed up a little. These are used in pairs for antenna diversity. Bolt these to the top plate above the side skirts... you will need some slightly longer m2.5...
thingiverse
There are 3 parts (all in mm) : Camera protection : this goes under the Vortex front bumper plate and is meant to protect a camera that protrudes under the bumper. Camer protection top : this is meant to stabilize the bumper plate and reenforce the...
thingiverse
Bumper reinforcement protector for immersionrc vortex 285
thingiverse
Vortex 285 HS1177 fpv camera support Print Settings Notes: Printed in Filaflex
thingiverse
Simple D4R-II case for_vortex 285 Print Settings Printer: DaVinci-jr Rafts: Doesn't Matter Supports: Yes Resolution: 0,1 Infill: 50%
thingiverse
15° Xiaomi Yi mount for the ImmersionRC Vortex 285 Racing Quad Use Zipties to mount Please upload a photo of your make. This design is not for commercial use or selling! Du möchtest dieses Teil haben? Schreib einfach: Facebook:...
thingiverse
Vortex 285 battery saver... bolt this above your plastic side to stop your props from ripping your packs when crashing! Use the longer M2 self tapping screws that come in your crash kit. ...See combined antenna mount version also -...
thingiverse
45 degree antenna mount to suit IRC Vortex 285 racing quad. Side and rear facing versions. These can be used in pairs or print one of each for even better diversity. Bolt these to the top plate above the side skirts... ...you will need some slightly...
prusaprinters
15° Xiaomi Yi mount for the ImmersionRC Vortex 285 Racing Quad Use Zipties to mount Please upload a photo of your make. This design is not for commercial use or selling! Du möchtest dieses Teil haben? Schreib einfach:<br/> Facebook: <a...
thingiverse
The Vortex 285 is a nice quadcopter, but a simple shock may let the propellers severe the battery. You can see what happens then on the last photo, and the landing was quiet soft. This cradle is to protect the battery from the propellers, when arm...
thingiverse
This thing is supposed to protect the battery of your Vortex 285 drone from your props, if the arms fold in! The extra bumps on the side help to absorb lots of force. It also protects the SMA connector, and the antenna in a crash. I found it...
myminifactory
Been wanting to hang mine and my wife's Vortex 285's on the wall for a while now and finally got around to designing a mount for it seeing as I couldn't find any. This one angles the quad 30 degrees off the wall to make your quad pop a little rather...
thingiverse
... protector at the bottom of the Vortex breaks easily, so I've made my own to be 3D printable... ...It is still possible to break the 3D printed version but I've split it into 2 parts so you can just print lots of the front to bring when you go flying...
thingiverse
THIS THING IS NOW ON MyMiniFactory AND SHALL BE UPDATED THERE ONLY https://www.myminifactory.com/object/3d-print-100254 ---------------------------------------------------------------------------------------------------------------------...
thingiverse
This is a Remix of The Vortex Bumpers (just the Front) for bigger Cams like HS1117 and other... ...update: cleaned it up and mede it bigger
thingiverse
I think this design is lighter than similar parts, but difficulty in printing, after printinting this parts you must use glue or solvent weld for you plastic. Also i include full model (from 2 pars), but it needs mutch more support. Print Settings...
cults3d
Various replacement parts for the Vortex MOJO 230 : Landing skids (choice of ABS or TPU, they will in any case be much more resistant than the original ones) the antenna clamping nut (made of ABS) The tightening nut can be used for any UAV and is not...
thingiverse
This is a combined antenna mount and battery saver for the ImmersionRC Vortex 285. This will guard your battery against props when the front arms fold back after a crash or knock. You will require 1 for each side. Use the longer M2 self tapping...
thingiverse
love the punisher and wanted to pimp my vortex up with a little punisher detail.
thingiverse
Never was printed on 3d printer, better use original carbon parts.
cults3d
I made this model of Zhongli's weapon, Vortex Vanquisher, which has separated parts so it can be painted easily You can also put LEDs on it too so it can light up! ... In this 3D print, use 1" PVC as the spear's stick, so you can save time and budget ...
thingiverse
This is a camera top plate for the Immersion Rc Vortex 285 to mount the Blackbird 3d FPV camera case
thingiverse
These are the clamping parts for the oem version of the vortex, included is the c clamps, the hex spacer and the main cf boom pivot clamp. ...https://www.facebook.com/groups/1600216723598853/
thingiverse
Parti disegnate da me per riparare e rinforzare il Vortex 250 PRO