vortex pro 3d models
73239 3d models found related to vortex pro.thingiverse
Vortex pro 250 Gopro session mount How I Designed This Autodesk 360 fusion
thingiverse
Just a simple camera mount I made for the runcam 2hd for the vortex pro ziptie it on and be done !
thingiverse
This is a remix of the 8m Prop Wrench by brentmc79. ... I found it a little too large for the prop nuts on my Vortex Pro. ... So I made this one a little smaller and labeled the top so you know what size it is.
thingiverse
... ... I designed it specifically for the ImmersionRC Vortex Pro but you can probably use it with other frames. It uses coffee stirrers for the antenna tubes. The antenna folds flat for transport and to keep it from breaking in the event of a crash.
cults3d
Easypeasy motor protection for ImmersionRC Vortex Pro. ...Works perfect with Ninjaflex.
thingiverse
Easypeasy motor protection for ImmersionRC Vortex Pro. Works perfect with Ninjaflex. ...Print Settings Printer: ZYYX 3D Printer Rafts: ...
thingiverse
Vortex pro 250 silicone dampers retaining pins and circlips
thingiverse
This is a camera mount for the vortex pro. It has a 33 degree angle. ...Fits a gopro session or any other gopro style camera!
thingiverse
Vortex 250 Pro - Mount for FrSky X4RSB. ... Designed for my personal use :) Post-Printing
thingiverse
A 20degree HD Mobius mount for a Immersion R/C Vortex Pro 250 quadcopter. Mobius can be strapped either front or back and allows room for most antennas behind the mount plate. Allen screws are accessible underneath the plate by moving plate to the...
thingiverse
By popular demand from the internet a 30degree HD Mobius mount for a Immersion R/C Vortex Pro 250 quadcopter. The additional 10 degrees allows for better camera angle during fast forward crashes and flights. The mobius can be strapped either front or...
thingiverse
A Remix of the first protector, this one here is stiffer and don't need the original pads anymore. Its printable in PLA or TPU/TPE. ... Print Settings Printer: ZYYX 3D Printer ...
cults3d
A Remix of the first protector, this one here is stiffer and don't need the original pads anymore. ...Its printable in PLA or TPU/TPE.
thingiverse
... to one of your choice. I have printed this in PLA and at only 1mm thick it is very bendy but stiffens up quite nicely when all bolted together. I have used this with the Vortex 250 Pro Racing Kit, Bumpers and Pimp Kit and all fits together nicely.
thingiverse
This mount is specially made for the runcam swift. ...It's inspired by the popular hs1177 mount for the vortex pro! ...Enjoy.
thingiverse
This is my design of a Vortex 250 Pro compatible Gopro Hero 3 Housing. It should prevent the Gopro from scratches and damage during crashes. All buttons and LEDs are accessible only the screen and the wifi button is not available. But normally i...
thingiverse
... in order to protect the camera (HS1177, runcam swift or foxeer) during the crashes, especially with a 2.1mm lens. ...I use it on my 2 vortexes with HS1177 and I love it ABS is advised, but it works pretty well with flexible filament like ninjaflex
thingiverse
This is a GoProSession mount with an 35° or 40° angle for the Vortex 250 Pro. Variations regarding the angle should be easy to make, so just leave a note. I printed this on the Ultimaker 2 And support set to "touching buildplate". But it shoud also...
thingiverse
This is a side plate for the Immersion RC Vortex Pro 250 with a sleeve for a 3.5mm OD antenna tube for receivers mounted internally. ...The antenna sleeve is angled at 45 degrees in the center of the part to allow the mounting of one antenna on each...
thingiverse
This is my 30 degree inclined mount for the Runcam 2 HD for the Vortex 250 Pro. ... It can be mounted without taking the carbon plate apart (and therefore without taking the whole copter apart) Enjoy Stanley
thingiverse
I wanted to use my Vortex Pro for movie purposes and therefore needed another angle than the 30° mount it comes with. It is precisely fitted for the slots of the original camera mount. As I use the Xiaomi Yi I wanted to use the onboard voltage...
thingiverse
Another flight camera mount as requested for a RunCam 2 to fit on the Immersion R/C Vortex Pro 250 quadcopter. Crash harder, fly faster with a 30 degree angle and capture all of it with a RunCame2. Straps should fit either front or back and allows...
thingiverse
Hi all, this is a part inspired from the ImmersionRC LED diffuser which will be available as an upgrade. Here you have the .stl file to print it yourself with translucid filament. ...If someone is able to remix it with some "triangles" on it to better...
thingiverse
Replace damaged lens holder ring on ImmersionRC Vortex 250 pro drone. ...
thingiverse
Parti disegnate da me per riparare e rinforzare il Vortex 250 PRO
thingiverse
Support Gopro Pour Vortex 250 Pro Print Settings Printer: Prusa i3 Hephestos Resolution: 0.2 Infill: 25
thingiverse
This is my design of a cam skid plate. ...It will protect the cam or your Vortex 250 Pro on landings in grass of somewhere else. Also in crashes :-) Please hit "like" if you like & download it. ...Thanks Stanley