voxelab aquila 3d printer files

However I noticed that for the Ender 3 clone, Voxelab Aquila, the ENDER3_4MM_8.17 light bar collides with the longer lower screw of the hotend carriage. I simply trimmed off 3mm from the bottom which should give clearance without having too big of an...

X and Y Tensioner belt covers for Voxelab Aquila X2.Cover your tensioner belt ports and disallow foreign objects into the openings.Simply pop in and go Note: The X axis will fit all 4 sides. ...Due to the way of the design of the cover, these do not fit...

Have been printing up the parts for the Voxelab Aquila chain from antibimmer's release here (https://www.thingiverse.com/thing:4725903) but liked the hot end design from CazGaming here (https://www.thingiverse.com/thing:4941347) as it aligns with the...

After installing the Voxelab Aquila - OOTBDD (Out Of The Box Direct Drive) by FedorSosnin, I had only one simple problem... Loading the gosh dang filament! For some reason I just couldn't get it to load properly. It would inevitably roll around the...

This is a remix of Ender 3 Pro PSU Meanwell LRS 350 PSU Honeycomb Cover by qrrak https://www.thingiverse.com/thing:4571351 and Voxelab Aquila/Ender 3 v2 PSU Cover with cable management by ddonnie https://www.thingiverse.com/thing:4831917 Hopefully...

I settled for one that is 10cm longer and angled in at 9 degrees.Pictures are of the updated endstop and arm.Print SettingsPrinter:Voxelab AquilaRafts: NoSupports:NoResolution: 0.2Infill:20%Filament: Hatchbox PLA BlackHow I Designed...

Convert the Y-axis of your Voxelab Aquila into Linear Rail. Non Invasive so you can go back to wheels at any given time. It was inspired by: https://www.thingiverse.com/thing:4553090 which I use on my Artillery Sidewinder X2 and I'm satisfied of it...

Remixed to work with the stock Aquila Extruder.

However, you might get away with not doing it at all. Note: The cable connecting to the mainboard is out of scope for this thing as I have replaced my H32 mainboard with a different one. Important: Make sure your line width is not too big as it may...

Wanted to use this system on my son's Aquila so I just remixed the extruder mount by PenitentHollow to fit the slightly different metal plate that holds the extruder and z-axis rod. ... The bottom connector by Ilueen...

Wanted to use this system on my son's Aquila so I just remixed the extruder mount by PenitentHollow to fit the slightly different metal plate that holds the extruder and z-axis rod. ... The bottom connector by Ilueen...

After I dug around trying various direct drive extruders for my Voxelab Aquila, many were horrible to print, and none of them quite had everything I wanted, so I designed this one. Design goals: 1. Be easy to print, with minimal supports and...

I adjusted the mounting holes so that it matches up with the Aquila X2 carriage plate.

Together with the STL files, I post the source files in the Kompas-3Dv18 format and CAD files in the STEP AP242 format. Added archives by file types to the download. All comments, remarks and remixes are welcome. Perhaps someone will make a more...

Additionally I beefed up where the link attaches, and included a file for a beefed up link. ...I found that the original links sag under weight with time (and I was having the worst luck with snapping them in my dumb giant hands trying to clip them...

Remix of mszoomy's Aquila Logitech C270 mount for any standard 1/4-20 mount webcam. ... Includes camera mount bolt

This direct drive setup is compatible with voxel lab Aquila and ender 3 ect... ...lightweight easy and quick to install.

The file I modified can be found here: https://www.thingiverse.com/thing:4792632 All I did was raise the part cooling vents 2mm so they are not so close to the print bed on the Aquila. I also created a version of this shroud with no BL Touch...

The file I modified can be found here: https://www.thingiverse.com/thing:4792632 All I did was raise the part cooling vents 2mm so they are not so close to the print bed on the Aquila. I also created a version of this shroud with no BL Touch...

E3D Minimalist for V6 & Volcano on Creality CR10/S Ender 3/Pro and clones by mediaman's : https://www.thingiverse.com/thing:3393889 I put the Voxelab logo on the bracket. ...That's all I've done.

Strange artifacts and a hole appeared when I sliced the original file by gminor in Simplify3D so I ran it through Tinkercad and filled the low spot Category: 3D Printer Accessories

23.30mm tall Dual Gear Extruder, Mount for Direct Drive Use all original hardware for your Aquila calibrated my E steps and got my retraction down to 2mm with out stringing

The included files should allow you to convert Voxelab's proprietary hot-end to a Micro-Swiss style all metal hot-end. Besides being an upgrade to the strange heatsink design, also allows the use of standard MK8 threaded nozzles. The adapter fits...

LCD screen cover with Micro SD adapter slot and storage for 6 Micro SD cards This is my first try at remixing, I loved the SD holder but it was not designed for an Aquila, and the opening for the reader was too big. I also used Tinkercad for the...

One strange difference between the Ender and the Aquila is the X-limit switch location. The housing for the Aquila positions the limit switch further into the board. As a result, the nozzle couldn't physically touch the last 7mm of the bed. So I...

... model that the space by the lower screwhole was a bit thin and cracked when they tightened it. ...I decided to remedy that before I printed one for my Aquila. This remix adds three reinforcement spines in that location to beef it up a little. ...

This is an adjustable back plate mount for the voxel lab aquila LCD screen.(WARNING)" stock screw are too short to screw into the frame of the screen" Use a little bit longer screws for best fit. Used washers for smooth adjustments and spacing...

Aquila extruders are not compatible with TPU filaments. When overloaded, the TPU filament comes off the guide rollers. I devised a guide cap to solve this problem. It can be used just by inserting it. The filament is PETG. The resolution (Z)...

I was coverting my Aquila to direct drive, i found @FedorSosnin direct drive mount, problem was that it was using the stock extruder and i was using the dual gear one: https://de.aliexpress.com/item/1005001431887581.html I found the remix of...

Remixed to allow printing upside down. For redesigned version without bevel: https://www.thingiverse.com/thing:5267251 Category: 3D Printer Accessories