voxelab proxima 3d

... to print TPU and Flex Filament. I also used a 25mm Aluminium pipe but i put the end caps inside the pipe. The spool holder fits for the Flashforge Finder 3 and Artemis. I thing it will fit also to the Voxelab Aries but this is not confirmed.

Modified this to work for my Voxelab Aquila X2 for the "Upgraded Kette groB" chain links. I also had to shave a little off the front inside sections and the side close to the threaded rod. Without the modification, it would slightly touch it so I...

X and Y Tensioner belt covers for Voxelab Aquila X2.Cover your tensioner belt ports and disallow foreign objects into the openings.Simply pop in and go Note: The X axis will fit all 4 sides. ...Due to the way of the design of the cover, these do not fit...

This is a remix of https://www.thingiverse.com/thing:4079159 to use on Voxelab Aquila. My modifications include: - 5mm shift to align guide with stock extruder - 0,5mm trim from the bottom, as stepper motor prevented easy mounting. - Slight...

This is a remix from the HMG5 gantry adapter "Ender_3_v2_OEM_Gantry_Adapter_9A" to better fit the X-Axis mount on the Voxelab Aquila. It still needs tweaking, unfortunately I haven't had the time to get it perfect and the wife has conscripted my...

Created these bases for my Voxelab Aquila. This consisted of extending the left side of the base and adjusting the location of the screw hole to fit on the Aquila.Did this for the Blokhead / Bullseye base as well as the v2 Petsfang base. ...Original...

So I modified ianewby's hot-end mount to accept the voxelab chains. Additionally I beefed up where the link attaches, and included a file for a beefed up link. ...I found that the original links sag under weight with time (and I was having the worst...

Created these bases for my Voxelab Aquila. This consisted of extending the left side of the base and adjusting the location of the screw hole to fit on the Aquila. Did this for the Blokhead / Bullseye base as well as the v2 Petsfang base. Original...

However I noticed that for the Ender 3 clone, Voxelab Aquila, the ENDER3_4MM_8.17 light bar collides with the longer lower screw of the hotend carriage. I simply trimmed off 3mm from the bottom which should give clearance without having too big of an...

This thing fixes a major design flaw with the voxelab aquila and ender 3 v2. The original PSU shroud completely blocks the vents which allow for airflow inside the PSU, causing the fan to run almost 100% of the time and likely shortening the life of...

It is top entry instead of bottom entry (like stock Voxelab Aquila), because I hate flipping the printer on its side to get to the mainboard. T.he SKR 1.4 (and turbo) only just fit so wiring is a faff. Also, I use octoprint with a PI contained in...

I wanted to try out direct drive on my Voxelab Aquila and I wasn't sure if the models for the Ender 3 would work on the Aquila because things are slightly different between the two printers. I ended up modeling a mount using my own measurements...

1-4-2023 CR-touch version added 12-3-2022 V2 added with and without BLtouch mount VOX FANG is a fang style shroud for the Voxelab Aquila, Aquila X2 & Aquila C2 (They all use the same hotend so it should fit all 3) *Uses stock fans *Has BL touch mount...

This is a remix of Ender 3 Pro PSU Meanwell LRS 350 PSU Honeycomb Cover by qrrak https://www.thingiverse.com/thing:4571351 and Voxelab Aquila/Ender 3 v2 PSU Cover with cable management by ddonnie https://www.thingiverse.com/thing:4831917 Hopefully...

After installing the Voxelab Aquila - OOTBDD (Out Of The Box Direct Drive) by FedorSosnin, I had only one simple problem... Loading the gosh dang filament! For some reason I just couldn't get it to load properly. It would inevitably roll around the...

... and clamp). File the through hole to give a smooth transition (I used a larger drill bit and angled it to take off the top edge of the hole). The M3's utilise some pre-drilled and tapped holes that are on the extruder shelf on the Voxelab Aquila.

This is a remix of Ender 3 V2 / Pro motherboard cover for 80X25mm fan (no support)' by scaryPug Designed to fit Voxelab Aquila. This cover houses 80x25mm fan. An lm2596 mount with screw added, please make sure your lm2596 fits in this cover because...

Have been printing up the parts for the Voxelab Aquila chain from antibimmer's release here (https://www.thingiverse.com/thing:4725903) but liked the hot end design from CazGaming here (https://www.thingiverse.com/thing:4941347) as it aligns with the...

this is a remix of thing:4915344, the wheel does work OK as in the original design, but the detent part doesn't fit on the Voxelab Aquila's Y-carriage plate on it's power-side (back left), though there's another remix that already fix this into a...

I wanted the stowable pi cam mount on my printer, but the Voxelab Aquila is a clone of an Ender 3 V2, not an exact copy -- the Aquila x-axis mount gives the original Stowaway Pi Cam for Ender 3 ( https://www.thingiverse.com/thing:3426025 ) nowhere to...

Convert the Y-axis of your Voxelab Aquila into Linear Rail. Non Invasive so you can go back to wheels at any given time. It was inspired by: https://www.thingiverse.com/thing:4553090 which I use on my Artillery Sidewinder X2 and I'm satisfied of...

Customized Hero Me Gen7 v2 base for the Voxelab Aquila printers.Created this because I found the original design a little bulky (required gantry adapter and hotend mount). Additionally, DD mounts were limited to front and back (wanted side for better...

The included files should allow you to convert Voxelab's proprietary hot-end to a Micro-Swiss style all metal hot-end. Besides being an upgrade to the strange heatsink design, also allows the use of standard MK8 threaded nozzles. The adapter fits...

Customized Hero Me Gen7 v2 base for the Voxelab Aquila printers. Created this because I found the original design a little bulky (required gantry adapter and hotend mount). Additionally, DD mounts were limited to front and back (wanted side for...

This is a cover for the Voxelab Aquila printer's mainboard. It allows for the installation of a larger/quieter fan. Unfortunately, the 80mm fans out there are usually not 24V fans, so you have to install a buck-converter to get the 24 volts from...

After I dug around trying various direct drive extruders for my Voxelab Aquila, many were horrible to print, and none of them quite had everything I wanted, so I designed this one. Design goals: 1. Be easy to print, with minimal supports and...

The lower and upper parts are also available in two versions - with the Voxelab logo and without the logo. Together with the STL files, I post the source files in the Kompas-3Dv18 format and CAD files in the STEP AP242 format. Added archives by file...

Strange artifacts and a hole appeared when I sliced the original file by gminor in Simplify3D so I ran it through Tinkercad and filled the low spot Category: 3D Printer Accessories

Remixed to allow printing upside down. For redesigned version without bevel: https://www.thingiverse.com/thing:5267251 Category: 3D Printer Accessories

However, you might get away with not doing it at all. Note: The cable connecting to the mainboard is out of scope for this thing as I have replaced my H32 mainboard with a different one. Important: Make sure your line width is not too big as it may...