vr headset for 5.5 inch phone 3d models
2641727 3d models found related to vr headset for 5.5 inch phone.thingiverse
VR headset with 5 inch HDMI display ----------------------------------- As a basic body, I have a simple VR glasses for smartphones it is cheap on ebay or from China to get used. The display is a 5 inch HDMI TFT touch display for the Raspberry Pi. ... ...
cults3d
This is a 3d printed version of a cardboard for 5" smartphone (here a Samsung S4 active). ... The lens and magnets come from a cardboard set I'd buy on amazon.
thingiverse
This is a 3d printed version of a cardboard for 5" smartphone (here a Samsung S4 active). The lens and magnets come from a cardboard set I'd buy on amazon. Print Settings Printer: Wanhao Duplicator 4 Rafts: No Supports: Yes Resolution: 0,3 Infill: 20...
thingiverse
Rubber bands will attach any size or shape of phone to this headset nicely.) Also recommended: 3 X 0.5" neodymium magnets. 2 on the outside, one on the inside. 1.5" elastic for headband. Foam Padding for head comfort. : I modified my previous...
thingiverse
... slip down, and I happened to look for some weight to put on the back so it becames more balanced. A broken 2.5' hdd just came into my sight... It even have it's own screw holes! So there's another back plate which you can attach a 2.5' hdd onto.
thingiverse
this is a vr set i made for the 5 or 5s. ...do not scale it up or else the phone won`t fit in it,
thingiverse
Suport for mobile phone, generic for 5 and 5.5 inch. ...Tested in Alcatel Pop 4 Plus, Huawey G620s, Huawey Y625.
thingiverse
... ...Loops at the back are to secure cord with small ziptie. Works best for getting a downward angle. You may need to scale up by 2540% to change from mm setting. ... Remixed from PS4 Camera Clip here: https://www.thingiverse.com/thing:1884607
myminifactory
These are phone holders for iPhone 5, iPhone 5s, iPhone 6, iPhone 6s, Samsung Galaxy S5 and Samsung Galaxy S6 for 3D Print N Pack's virtual reality headset kit. See the rest of the project at: https://www.myminifactory.com/object/15157 Use this...
thingiverse
It will snap into and act as a hinge with my headset here:http://www.thingiverse.com/thing:634518 Or it will latch onto the original Note4VR headset here:http://www.thingiverse.com/thing:554259 But that will leave you with a loose piece to keep...
thingiverse
Customized version of http://www.thingiverse.com/thing:634492 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=634492 Instructions Using the following options: phoneHeight = 83.5 phoneDepth = 13.5
thingiverse
Customized version of http://www.thingiverse.com/thing:634492 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=634492 Instructions Using the following options: phoneDepth = 13 phoneHeight = 70.5
grabcad
Modular design of a VR Headset for phone. Dimensions specific to Motorola Moto G Power. ...Hooking mechanism to attach to headgear if needed.
thingiverse
Suitable for any phones form factor 5.5, probably not only (as in the smaller and in a big way). Due to the center of gravity shifted back and the increased area of the base, the stand is very stable even when the phone is placed vertically. ... ...
thingiverse
while using this don't forget to be careful at the traffic around you, I will not be responsible for any broken bone/phone x) Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.3 Infill: 100 Notes: printed the whole thing and held...
thingiverse
Holds your phone/table on the front of your pc. Kinda flimsy lmao. Space the holder part off with washers if the bay mount doesn't sit flush with the front of your case. ...Use m3 nuts/bolts.
thingiverse
This is a headphone/headset desk holder for desks of about 28,5 mm diameter. It is especially designed for HyperX Headsets but it surely fits for other brands. You can print it on the side without supports. ...Also, I printed it on 100 mm/s which...
thingiverse
Adapter to use smaller lenses with the OnePlus One VR Headset, thing 686737. ... As I had the smaller 25mm lenses on hand I needed an adapter from 35mm to 25mm and adjust the position of the lense.
thingiverse
Adapted a model of an FN FAL for use with the 5.5 inch scale Doctor Who figures, should be roughly in scale. Would only recommend resin printing this. ...Be wary of the barrel being thin and fragile.
thingiverse
Whipped this up super fast. ...It's a hook for a headset that will snap into one and a half inch square stock. ... It's got a 1.5" cutout, so you slide it onto the bar at an angle, and rotate it to lock in place.
thingiverse
This is the board I ordered: http://www.aliexpress.com/item/1-x-HDMI-VGA-2AV-AUDIO-Controller-Board-For-5-6Inch-TFT-HYUNDAI-HV056WX1-100-HV056WX1/32268599169.html LCD:...
thingiverse
... I'm a Youtuber, and I don't have a tripod or anything. ...So I always have to do all my shots handheld. NOT ANYMORE! Now I've designed the VR headset and I can 3D print it to say goodbye to holding my phone like an idiot while recording B-Roll.
thingiverse
Mount for a Waveshare 5.5" display (https://www.waveshare.com/5.5inch-1440x2560-lcd.htm) in a Gear VR to create your own stereoscopic VR goggles. ...Cutouts for the USB and HDMI required to power the display and connect it to a PC.
thingiverse
This is a phone stand for phones with a 5.5 in diagonal. Fits the iphone 8 plus and other 5.5 in screen phones. May not fit smaller phones. The feet are just out of the way of the screen size. Providing minimal impact on phone use. Viewing Angle...
thingiverse
Angry Bender robot eyes! ...Meant to attach to the front of your VR headset. I recommend using 3M poster tabs. Designed around the Oculus Quest curvature but should work for any headset.
thingiverse
this is a phone holder that goes into the space under shifter. ...i haven't printed it to see how it fits but going by measurements it should be close. might have to adjust stuff for your phone size.