180mm Hunter Vtail Quad Parts

thingiverse

3d printed parts for 180mm Hunter Vtail Quad, link to carbon parts will be available when finalized.

Lynxmotion Hunter VTail 500 Replacement Landing Gear

pinshape

The vtail spiraled down and I lost one gear and the arm attached to it. The other two were mud covered but held up strong! InstructionsThis is printed on a Dimension 1200es out of zABS material. It is a direct mount up to the existing support...

Lynxmotion Hunter VTail 500 Replacement Landing Gear

thingiverse

The vtail spiraled down and I lost one gear and the arm attached to it. The other two were mud covered but held up strong! Instructions This is printed on a Dimension 1200es out of zABS material. It...

EACHINE 210 VTail

pinshape

Summary stronger VTail-Bridge

EACHINE 210 VTail

thingiverse

stronger VTail-Bridge

Mini Talon Vtail Stabilizer

thingiverse

Mini Talon Vtail Stabilizer

Delta_Vtail_S300

grabcad

Small RC airplane with fuselage wing blending, 2 rear electric engines and Vtail.Scale 1/24 model for concept design review and aerodynamic simulation and testing.

lidl glider xl vtail

thingiverse

Vtail for lidl xl glider. All ready plited for 3 piece for easy print . ...I did 0.2 layer , single shell 5% infill 2 bottopm/ 2 top solid.

Viper Recon Vtail quad

grabcad

so I designed a servoless tircopter using a Vtail with custom mixing. This would have worked a lot better with a proper flight controller, but the results were not too bad using mixing and simple gyros. at the time I thought I may have been the...

Micro Vtail hexacopter

grabcad

it is actually a pentacopter with Vtail. Special motor partition table is needed in order to have stable flight. Tested with Betaflight, Inav and arducopter 4.xx. Fly beautifully with amazing yaw control. 1408 3600kv motor @4s 1400 give 7m flight...

Eachine Vtail Camera mount

thingiverse

This is a camera mount for the Eachine Vtail 210. The camera is quite good but vulnerable to damage. This mount allows you to: a) attach the camera to the board b) prevent damage to the ribbon cable c) allow the camera to be easily removed and...

HUNTER

grabcad

HUNTER

Hunter

grabcad

Hunter O1,v1 Novus ordo seclerum

Hunter

grabcad

Hunter O1,v1 Novus ordo seclerum

Hunter

sketchfab

Hunter made in 3dc. Zbrush for retopology. ...Blender for posing.

Hunter

sketchfab

Hunter from the spyro series, model based on my own design

Hunter

sketchfab

The hunter is one of the creatures I was tasked with making for Nightmare Grotto

hunter

thingiverse

Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockLength = 10 Name = Hunter Smith BlockWidth = 5

Hunter

sketchfab

The hunter figure is said to symbolize the origin of the city name, which comes from the word Strzelec (hunter). The fountain with the bronze memorial was designed by Peter Lipp in 1929 on behalf of the Magistrate of Groß Strehlitz and built by the...

hunter

thingiverse

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 1 message = hunter font_thickness = 5 hole_radius = 3 stick_thickness = 3 stick_width = 8 Font = write/orbitron.dxf font_size = 10

Hunter

thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 3 hole_radius = 3.5 Font = write/orbitron.dxf font_thickness = 5 stick_width = 10 flat_bottom = 1 message = Hunter font_size =...

Hunter

thingiverse

Table: The Hunter Level Proficiency Bonus Features Hunter's Hatred Dice Spells Known —Spell Slots per Spell Level— 1st 2nd 3rd 4th 5th 1st +2 Hunter's Hatred, Hunter's Companion 1d4 — — — — — — 2nd +2 Spellcasting 1d4 2 2 — — — — 3rd +2 Hunter...

Hunter

cults3d

Table: The Hunter Level Proficiency Bonus Features Hunter's Hatred Dice Spells Known —Spell Slots per Spell Level— 1st 2nd 3rd 4th 5th 1st +2 Hunter's Hatred, Hunter's Companion 1d4 — — — — — — 2nd +2 Spellcasting 1d4 2 2 — — — — 3rd +2 Hunter...

Hunter

thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: font = write/orbitron.dxf fontsize = 8 corner_radius = 3 text_style = -80 line_10 = slitwidth = 4 slitlength = 12 line_9 = line_8 = line_7 =...

Hunter

thingiverse

Update 01Apr2017: I have cut the hunter into pieces so that he can be reposed. I am using TinkerCAD for the posing because it makes combining all the pieces via boolean a lot easier. The pieces are not made to be printed separately (yet) so you...

Hunter

thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: borderextruder = extruder4 lug_length = 4 font_style = bold font_weight = 0 font_outline_style = rounded bar_thickness = 2.4 inner_margin_width =...

VTail Quad

grabcad

This is my design for a V Tail Quadcopter which I have named "Raptor". ...I am aware that it bears a resemblance to another product on the market, but what can I say; imitation is the sincerest form of flattery.

RC basic trainer, Vtail and Pusher

grabcad

Purpose:Design, build and test a Radio Control basic trainer airplane , type Vtail and pusherGeneral requirements:KISS logic, Low cost, Home build (DIY), Small size.Hand launched, Crash landing. ...Overall dimensionsSpan <1m,...

aerial drone canopy for the Robotshop Vtail quadcopter

pinshape

Summary aerial drone canopy for the Robotshop Vtail quadcopter

aerial drone canopy for the Robotshop Vtail quadcopter

thingiverse

aerial drone canopy for the Robotshop Vtail quadcopter