vuse alto case 3d models
205489 3d models found related to vuse alto case.myminifactory
a case for the Vuse Alto vape kits, keeps pocket lint out and keeps ya from fidgeting with the cartridge, and is leak proof for the most part. ...I had to so a bunch of iterations before i got it right but u may need to print it @ 101% scale if its too...
thingiverse
A case for the Vuse Alto vape kits, keeps pocket lint out and keeps ya from fidgeting with the cartridge, and is leak proof for the most part. ...I had to so a bunch of iterations before i got it right but u may need to print it @ 101% scale if its too...
thingiverse
This is a Vuse Alto charging dock designed to hang off of a desk
cults3d
Design for a Vuse Alto to fir perfectly, just add your own lanyard necklace.
cults3d
a simple belt clip for the vuse alto v2 simple v4 has a small knub to hold it in better
thingiverse
A simple stand for the Vuse Alto that holds two boxes of vape pods for a neat, organized appearance. The USB charging cable pushes in from the top of the right opening, and then the magnetic connector should fit snugly into the opening. ...The cable is...
thingiverse
This is a charging dock for the Vuse Alto. It uses the factory magnetic charging cable. Just insert the USB plug in from the top, press fit the magnetic end into the hole in the top (this is a tight fit on purpose) then press the cable into the...
thingiverse
Open Concept Design For Holding and Charging Vuse Alto Pods and Batteries. For Personal Use Only Making another version with another set of hooks as well as making them slightly thicker.....shown in the second picture. have not uploaded it yet. I...
thingiverse
A holder for two Vuse Alto chargers, which secure the Alto at an angle, and has channels for the USB wires underneath to allow it to remain flat.
cults3d
case for electronic cigarette vuse epod 2. there is a cap on top to protect the pod, a cap at the bottom to be able to put in charge easily without removing everything. ... printed on sidewinder X2 start printing the bottom cap, if it is too tight or...
thingiverse
This is a vape case for Vuse ePod2 with a slot to attach an Apple Airtag This one was printed with flexible fillament it helps for trying to get the airtag in the hole.
thingiverse
Remix & redesign of source box specifically to fit standard 3-piece alto recorder. Print the box halves right side up & the cover halves upside down, no supports needed. I recommend using the 16-mm bolts when assembling as not all the holes are...
thingiverse
Has the size of Vandoren and Rico Reeds with cases Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 should work Infill: 50%
thingiverse
Vuse Charger Cut down the wire and solider them back. The USB side is a tad loose but the Vuse side is very snug. ...I added Superglue to bothsides.
prusaprinters
... ... This is another holder design but made for the Vuse Vape to help organize your desk. It is meant to hold 3 full devices, the right most spot is built to hold the charger (press fit), and the front 3 spots are for additional cartridges.
thingiverse
Customized version of http://www.thingiverse.com/thing:82533 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=82533 Instructions Using the following options: depth =...
thingiverse
Customized version of http://www.thingiverse.com/thing:51376 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=51376 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:384919 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options:...
thingiverse
SIMPLE DESKTOP HOLDER FOR YOU VUSE XL GO VAPE PENS NO SUPPORTS PRUSA STANDARD SETTINGS .20 AND 15% INFILL PRINTED WITH PLA IF YOU DOWNLOAD AND USE, SHOOT ME A LIKE THANKS FOR LOOKING AND HAVE FUN
thingiverse
ANOTHER BASE FOR VUSE ALTO, COMES WITH SIDE ATTACHMENTS TO HOLD JUICE. ONE MIDDLE SECTION HAS GROOVES FOR THE SIDE ATTACHMENTS AND ONE DOES NOT. ...THE CHARGER HOUSING MUST BE GLUED IN PLACE AND IT KIND OF SITS AT AN ANGLE AT THE END OF THE MIDDLE...
thingiverse
The Xerox Alto and Dorado have a number of plastic structural components that are under tension and succumb to age related brittleness. ...They can be replaced by printing the included painstakingly re-engineered STLs.
thingiverse
stand for vuse epod 2 charger should go into vuse_holder cable should go through vuse_stand hole I glued the vuse_holder and vuse_stand together the stand is not very stable and it falls over, so I recommend either gluing it or giving it some weight...