vw tool 3d models
110209 3d models found related to vw tool.grabcad
Rear brake caliber tool for Vw. ...Turns and pushes the piston to increase space for new brake pads
thingiverse
This is a project for an Intro to 3D printing class, I do not have a printer.
thingiverse
This is a fast-made tool to remove parts in your car. ...At the vw store this is meant as T10383/1.
thingiverse
Use this and a long screwdriver to extract your defective fuel pump without damaging your car or wrist. For instructions look at the video: https://streamable.com/w0it2 I dont know how many car types this fits, I designed it for my Golf 4 from 2002...
thingiverse
This is a tool to hide brake cylinder in VW Passat B3/B4 or Golf III. I tested it on Golf VR6 calipers, but it should work in other models. The disc is 55 mm diameter and pad is 100 mm long.To make it work I used a 606 bearing, M6 screw ald 3 M6...
thingiverse
Tool to remove plastic oil drain plug on Volkwagen Golf and Audi (#part number 06L103801)
thingiverse
I suspect this tool can be used on several Audi and VW cars (if the tool name appears in the manual). Please print with the handle down to get a smoot surface for the sim-ring. The version 2 is recommended to use with less problems for printing...
thingiverse
Tool to adjust the camshaft of VW T4 engines. ...Volkswagen tool number VW 2065A.
thingiverse
VW Beetle and Camper upto 1600 cc clutch alignment tool Hole can be tapped M8 to provide bolt for pulling out if needed
prusaprinters
... this tool instead. ...Use only the hand wheel to tighten, and if required use a ½" ratchet to loosen.This plug is found on a wide range of VW group vehicles.Best printed on its side as shown in the pic to ensure strength in the desired direction.
thingiverse
This is a wrench tool for those who have poor hand function to twist the wheel to mount or remove the detachable towbar on a Volkswagen T5 or T6. May also fit other cars with Westfalia detachable towbar. ... My T5 have a Westfalia 321 534 20 c45...
grabcad
IA quick 3D model and drawing of a VW T10252 Camshaft locking tool, good for building one and take measures off.This tool is for the EA113 FSI and TFSI engines.
thingiverse
Automatic preheater tool: Is a simple tool to reactivate the preheater in i.e. in VW T5 to survive the cold winter nights. The PoC will be an Arduino nano with a DHT11 and a small servo motor to push the button on the remote. Later on I thinking...
thingiverse
Another simple design. ...Based this on size as we are only ever two people travelling and I wanted everything theme based.
thingiverse
Just a couple of easily 3d printed engine rebuilding tools used for holding cylinders in place while you assemble/disassemble a Volkswagen Air-cooled motor for a rebuild. I fashioned 1 after a commonly available tool used for measuring deck height...
thingiverse
A little bit changed VW 3313 tool for fuel pump timing setup. Tested on VW T4 AJT. ...Works perfectly
thingiverse
For removing the stock radio for some Volkswagen vehicles. ... Created using measurements taken from the original tool for my 2004 VW Jetta.
thingiverse
Screw in one end of the 8mm threaded rod into bottom of the tool body, put the jamb nut on the 6mm bolt and screw the bolt from the top into the tool body. The 8mm nut secures the tool to the engine when it is mounted on the engine mounting hole. See...
thingiverse
Volkswagen Special tool #3104 for shift lever alignment Mk III Cabrio/Jetta/Golf
thingiverse
Seal puller VW681 special tool to remove shifter seal on Vanagon transaxle
thingiverse
... Mk2. ...You have a little flap in the mudguard that you side open and then try to reach in to unscrew the bulb holder, impossible without the use of a small handed helper, so I made this tool; I can now change bulbs in 15 seconds. ...Fill your boots.
thingiverse
Based on the off-brand tool i bought, which had a 3 or 4 degree advance on it (Hard to measure, but definetly 3 or 4). This model is set to 4 degrees, but the freecad source is included, so you can change it if you like. ... Print-settings are not...
prusaprinters
Thing name says it all :) Print Settings Rafts: No Supports: Yes Category: Tools
thingiverse
VW AUDI 3393 Subframe Alignment tool: measurements taken from original tool, alignment diameter 19,5mm, if you print it on big percentage infill it should be enough for the job :)
thingiverse
Helps clean carbon from the valves on various VW and Audi engines. Instructions and usage pictures can be found elsewhere. Originally designed to fit a BPY FSI engine. ... BPY, 2.0T, S4 3.0L Fusion 360 file: https://a360.co/2XFetag
thingiverse
Schlüssel Tool um die Verschlüsse des Gasfachs einfacher zu öffnen um dort die Flasche zu schließen oder auszutauschen.