w1209 user manual 3d models

Semplice organizer per schede user-port per computer Commodore 64 o Commodore128

Customize the user interface according to the specific requirements of each use case to optimize additive manufacturing capabilities.

A simple label maker for organizing cords and connectors within thunder::tech's User Experience Lab workspace.

Stand for a laptop and phone in one. ...Remix from user sysys: https://www.thingiverse.com/thing:2927632

This is a user customizable S hook (center balanced) that you can control the following parameters for (via Fusion 360 User Parameters): * Opening size of the top and bottom hook * Overhang (+/- degrees) of the hook * Diameter of the hook Some...

... in the connector. Both case parts are labeled with clear instructions: "THIS SIDE UP" and "THIS SIDE DOWN," serving as a crucial safety precaution against inserting the user port cart upside down, which could lead to significant damage and smoke.

... uploading issues that sometimes cause problems during measurement procedures, the necessary modifications can usually be made relatively quickly for improved results. Practicing users often encounter minimal issues with the upgrade process overall.

Users can attach specialized utensils, such as cups (which may be 3D printed), to the prosthetic through magnetic connection. An alternative option is the use of Polymorph, a plastic that shapes at 160°F, allowing attachment of various items like...

Cover for C64 User Port (24 pin) / Cassette Port (12 pin) connectors. ...Connector used: https://www.aliexpress.com/item/8-12-16-20-24-30-36-44-56-Pin-PCB-Slot-805-Series-Card-Edge-Connector/32848683961.html...

... D1 mini (ESP8266) board, but feel free to experiment with other options as well. The case cleverly accommodates the standard User Port connector in a dedicated slot, ensuring that connection loads are safely isolated from the PCB connection point.

You can clearly see LEDs 1 and 2 shining through the lid, and you have easy access to both the reset and user buttons as well. There is no way to reach any of the pins when the MSP430 is encased. ... Note: A screw with a thread diameter of 3mm is...

... ...My original blank keys are here https://www.myminifactory.com/object/3d-print-commodore64-replacement-blank-keycaps-109077 These few are for users to test if their printer can handle the resolution needed especially the face PETSCII characters.

One is blank on the sides and the other is labeled Admin and User. I printed these in resin and they broke easily until I switched to Siraya Tech resin. I imagine these can be printed on FDM printers just fine too and would likely be pretty...

This is my attempt to recreate the Starlink user terminal (Dishy) from photos and measurements online. Designed in three pieces, the dish, the stand and the pole section. Available on Onshape:...

These inserts can be used to key edge connectors like those required on the user port or cassette port of the Commodore 64. Properly keyed connectors will fit the correct way only and can no longer be reversed accidentally. The dimensions of...

I/O trim plate to for the user port area of Commodore 64 using the Ultimate 64 main board. This slides into the case before sliding the board into it. No modifications or screws needed to hold it into place. I have version 1.2 of the U64, I think all...

Enclosure for the Ultimate 64 Userport expansion that attaches to the Tape port.I also made a version that allow for access to the Tape Port: https://www.printables.com/model/752267-ultimate-64-user-port-combo-adapter Print Settings:Layer height: 0.2...

These inserts can be used to key edge connectors like those required on the user port or cassette port of the Commodore 64. Properly keyed connectors will fit the correct way only and can no longer be reversed accidentally.</p><p>The dimensions of...

Cover for C64 User Port (24 pin) / Cassette Port (12 pin) connectors. Connector I used: https://www.aliexpress.com/item/Sample-2pcs-Lot-805-Card-Edge-Connector-3-96mm-Pitch-2x6-Row-12-Pin-PCB-Slot/32539449444.html...

Here is the case and DIN rail mount for the w1209 controller. ...M3x14 screws are used, but it is better to use screws for plastic.

ENCLOSURE FOR HW-557 OR W1209 TEMP CONTROLLED SWITCH REQUIRES: 4X M3X8MM SOCKET HEAD CAP SCREWS 4X M3 HEX NUTS ENJOY!

Simple mount to secure W1209 controller onto a 12v/230v fan heater (with 60x16 fan). ... Screw the fan onto the uprights and clip the thing onto the fan.

Polysquare's Remix of Constal's W1209 Enclosure Scaled Up for Better Visual Impact. ...Check Out the Enhanced Design Here: https://www.thingiverse.com/thing:1707393

Just my version of back cover opened. ...I also create a sensor holder: https://www.thingiverse.com/thing:4661932

That is an evolution of existing project https://www.thingiverse.com/thing:1707393 made by "polysquare" which allows to install 12V connection plug and 12v buzzer inside of the box. ...

We require four M3 screws immediately.

It is flash with mounting surface. ...In case that surface is not flat you can heat edges and make them curve according to curvature of mounted surface for tighter fit and nicer look.

with added fins to screw against bottom plate

Are you looking for a simple enclosure to hide your PCB? You've found one!Assembly is pretty straightforward, here's what you need:1x Top cover (print)1x Bottom cover (print)3x Button (print)4x M3x10 bolt (you can optionally use M3x12 or 15)Allen...

The original design with spikes is extremely unreliable. ... Print Settings Printer Brand: RepRap Printer: mendel i2 Rafts: ...