walkera g 2d 3d models

... You just press it on and it clips to the gimbal holding the Gopro securely in place. It has tabs that allow easy removal too. This allows you to install and remove the Gopro from the Walkera G-2D gimbal in just a couple of seconds with no tools.

This is a quick Gopro mount for the Walkera G-2D gimbal. Based on the great design of the [G-2D quick realease rail by Grabejud](https://www.thingiverse.com/thing:2843686), this allows you to use your gimbal with all the gopro accessories. ... I use...

SJCam 5000X bracket for walkera G-2D Gimbal. Since the stock bracket doesn't fit to SJCam SJ5000X camera, I made myself one. The camera is a little bit larger than the gimbal plate, so I had to put some sticky thick foam tape on the plate to sit...

SummaryThis is a quick release system for the Walkera QR X350 Pro multi rotor that connects to the Walkera G-2D gimbal. It quickly and safely attaches/ detaches the G-2D gimbal to the QR X350. Simply fit together, slide back, then lock it into place...

This is a quick release system for the Walkera QR X350 Pro multi rotor that connects to the Walkera G-2D gimbal. It quickly and safely attaches/ detaches the G-2D gimbal to the QR X350. Simply fit together, slide back, then lock it into place with...

A completely new mount for the Xiaomi Yi on the Walkera G-2D ! The camera is flipped so it cand be used for FPV, like in the photos, either way, the cables where not accessible. Quick install guide below. Print Settings Printer Brand: ...

Mount your Walkera Gimbal with GoPro parts.

Walkera G-2D gimbal camera mount adapter for the Yi Action Camera. ... No soldering or flipping required!

Allows you to attach the Walkera Gimbal to the numerous Gopro mounts. ... I use it on my hand held mount to make it a steady cam.

Adaptation of 'GoproDummy1.skp' from here: http://www.thingiverse.com/thing:1126548/#files To allow me to mount on a Walkera G-2D without cutting/filing/sanding the gimbal. ...Print Settings Printer Brand: RepRap ...

Work in progress This is an adapter to allow you to mount your Walkera G-2D (plastic gimbal mount plate) to your DJI F450 Flamewheel. Fixing by x4 M3 bolt/washer/nut. Inspired by MP3III's phantom 2 adapter http://www.thingiverse.com/thing:966981 ...

My additions include holes for the microphones and the speaker, a hole to access the USB port on the side, and pre-punched holes for the Walkera G-2D gimbal arm screws. I have also added a hole on the bottom to access the 1/4" socket mount if you...

This mount allows you to remove the large Walkera anti-vibration mount from the G-2D gimbal and mount it on a smaller plate that mates with my F330 Landing Gear System. Check my other designs. The G-2D Gimbal Control Unit can be removed and mounted...

I also added a second set of holes for mounting the G-2D in case anyone to use 2 screws. Because of some clearance issues I had to make room for the landing gear to clear the adapter, so now it needs supports to print. I included a top part with...

I broke my hero4 and the stock mount is actutally kind of a pain to remove in order to put the camera in and out. I wanted to use my session5 instead but didn't see a mount. I found 2 designs on here and spliced them together. Had to add a little...

I found the Walkera G-2D gimbal on Amazon for about 70 Euro. Quite cheap and extremely lightweight. The electronic works fine and smooth. As I prefer an Mobius Cam over the GoPro Hero I created these conversion kit. With these kit you can convert...

Much stronger, better fitting than the original one I posted. ... It prints without supports

Good fit. Might need to rethink attachment if I can't find long enough screws. I'm not sure you need the supports during printing but I haven't tried. ... Best flip it onto it's back in the slicer to print.

I moved the gimbal/camera assembly aft a little over 1/2 inch to improve the balance. I reduced the size to reduce it's weight (from 12 grams to 9). Cleaned up the mesh. I have also included the obj file and an x3g for anyone that would like to...

Modified the original version to print without supports. ...Worked for me with PLA, 0.2mm layer on Prusa i3 MK2.

I calculated force and weight very carefully, so it works good. ... Stick the sensor of gimbal behind the trench behind by double sided tape (2 side tape) Use 2mmx15mm screws to hold the cam

I calculated force and weight very carefully, so it works good. ...Stick the sensor of gimbal behind the trench behind by double sided tape (2 side tape) Use 2mmx15mm screws to hold the cam

Stick the sensor of gimbal behind the trench behind by double sided tape (2 side tape) Use 2mmx15mm screws to hold the cam Print Settings Rafts: Doesn't Matter ...

This adapter allows you to connect a Walkera Gimbal G-2D to a DJI Phantom 1 or F40 without any modification to the gimbal or the Phantom. ...With this mount no leg extensions are needed.

This replaces the mounting plate on the Walkera G-2D Gimbal. I have no problems with the jello effect and with all of the ground clearance problems this gimbal (I imagine all gimbals have this problem) I decided to eliminate the cushion balls and...

Plate mount on Walkera G-2D Brushless gimbal. Plate and transmitter install using zip tie. ...Print Settings Rafts: No Supports: ...

This is a modified Top Plate for the F450 to put a Walkera G-3D between the front arms so it's mounted "TBS Discovery Style" but with "some" YAW freedom. ...It will "hang down" as it was designed to be used and (still beta) should be high enough to go...

For Xiaomi Yi walkera G-3D gimbal, G-2d gimbal.

Updated 8/3/2015 Remodeled in Designspark CAD, It is a much cleaner model now This is a complete mount to adapt the Walkera G-2D Gimbal to a DJI Phantom 1 and F40. It replaces the Walkera mount. I have included the gimbal mount with and without...

... who love cars and especially the mythical mercedes G-class. ... 2D design to stick on a wall or flat, you can also use the print preparation software to thicken the object to make it stand upright. ... Subscribe to my future 2D automotive design !