wall grommets for cables 3d models
2345279 3d models found related to wall grommets for cables.thingiverse
Holder for looped cables which screws to the wall. In addition to the printed parts you will need some broom handle (usually very cheap and widely available from DIY places), mine measured at 23.75mm which seems to be standard in the UK, though you...
thingiverse
Here is a small support for Dupont cables of any length! You can fix it everywhere, and you will better tidy up your workshop / office! To fix this small support, you will need just two small nails or a little bit of Patafix! Just share and pirnt...
prusaprinters
The holder consists a small compression spring that will fix the cable.The cable holder has space for a cable up to 8mm. Nice to have some in you toolbox in differen colors.Be carefull that you don`t damage the cable when you are closeing the...
thingiverse
Flange to run cable from interior to exterior (originally designed to run solar cables from roof racks into canopy) holes are made for 11x19mm rubber grommets
thingiverse
For longer Hifi- and other cables an needed another holder, so i made this. ... The holes are 3.5mm
thingiverse
This is a small wall hanger for cables, tools and more. ...It has 4 holes fro screws but you can use only two if the weight is small.
thingiverse
Wall mounted holders to organize all the usb-cables with different connectors. Each is 12cm long and the gap between the spikes is 5mm. Four different versions, three with text and and blank. ...
thingiverse
Cable tie wall mount It can be used by sticking it to wall or other surfaces with double sided tape Dimensions of the zip tie hole: 5 mm x 2.4 mm Total dimensions: 20 x 20 mm Inside dimension: radius: 3.5 mm
thingiverse
Robust stake, designed for tarps or other items with a #3 grommet (12 mm ID, 22mm OD). Usable length of 6". ...Should scale fine for smaller or larger grommets.
thingiverse
This is a tiny Wall Mount for a single Cable. If you print it in original size it fits only for Cables with a diameter of 3,5mm or less. The diameter of the Nail you need is 2mm or less. ... You also need a tiny hammer and a lot of tact for nailing.
thingiverse
This is a pair of small grommets, created to cover the holes I badly drilled to allow cables to come up from underneath. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Mini+ Rafts: Doesn't Matter Supports: Doesn't Matter Overview...
cults3d
Organize all the cables on the desk or work table and do not disturb can be difficult if the table does not have this type of cable grommets. In a simple way with a drill, a circular drill bit and two simple printed pieces you can at once organize...
thingiverse
... und Muttern M4. Simple wall outlet for extension cables with a plug permanently attached on both sides. For example for garden tools, pool filters, etc. Cable outlet 8mm. Wall thickness variable with screw length. ...M4 screws and nuts used.
thingiverse
Simple parts to dress up the top of base of any enclosure. ... Designed for 50mm thick. ... Print 2 of the wire grommets per hole.
prusaprinters
Simple wall cover for up to 3 Cable TV wires.Add the rim if it needs to raise up because of the wall box. ... Plug is for unused holes.CheersKisssys
thingiverse
I got this rubber grommets made for Corsair Obsidian Series® 700/800D PC cabinet.http://www.corsair.com/en-us/rubber-grommets-for-obsidian-series-800d I plan to use this in my heated chamber, then the wires that goes out of the box look nice.
thingiverse
I wanted to run Ethernet cables to the router, while still using the wall mount bracket. So I used ldymanow's design as a template and rebuilt the bracket in Fusion 360. I extended it out from the wall a little over an inch. I have included the...
thingiverse
I've made this simple thing to protect a gap between my Bekant table and the wall, so my cables don't get accidentally squished. =) I've also made this thing wide (3cm) so it won't turn when the table is pushed slightly sideways. Also, it was made in...
thingiverse
Made for 12mm drywall walls. It's adjustable and will fit anything 80mm+. Print with 50%+ infill, **threads upwards**. Drill a 35mm hole straight through the wall, plug one end with one piece and screw the other end in from the other side. ... Fits...
thingiverse
... too long to answer. For now here is a Pass-Through Wall Plate with a 1.5 inch square in the middle. Tested with PLA Layer Height 0.2mm Dimensions 5 x 3.15 Inches I'm hungry But not for food Anyways... ... *printer hums fade into background*
thingiverse
Furrion wants $6 each for these freaking things. F that. Print your own. You might need to use a 9/64 drill bit to clean up the hole after printing. I printed these with ABS. ...100% infil.
prusaprinters
This is a super simple grommet I pulled together when building my home network cabinet. Simply cut a 2" hole in your cabinet and screw this bad boy down in it. ... Voila!</p>
thingiverse
But it turned out that a bog-standard 2 perimeter wall, with a 20% infill, provided perfect compression properties for my machine. Not much of a design, I guess, but I hope someone can use it! I also think it's about time I looked at replacing...
thingiverse
... hole. Make sure you have the right screws. For the 2.5 inch drives he used M3X6 screws and all his heads fit but here's the sizing just to make sure yours will too: The inset into the grommet is 6mm diameter and the screw hole is 3.3mm diameter.
thingiverse
I designed those motor grommets to replace the ones on my qx 95, they also double as landing pads and protect the bottom of the motors! ...
thingiverse
Simple and small cable hook. ...Ideal for USB, audio, HDMI cables. Helps to arrange cables neatly under the desk or on the wall. Features 3 holes for mounting with standard screws. ...Takes about 40 minutes to print needs no support.