wall mount computer case 3d models
685794 3d models found related to wall mount computer case.thingiverse
Can be used with kickstand or mounted to the wall on thumb tacks. **I used the threaded inserts linked at the bottom, but included files that should work for tapping. I also used hex standoffs to mount the housing/board, but added files for...
thingiverse
Computer motherboard wall mounts, Should fit most motherboards. there is 2 sizes depending on how much room you have on your motherboard to work with. some spots may need shorter mounts then other spots depending on solder points, capacitors and...
thingiverse
For mounting an 80's computer on the wall using command strips. ... I used the interlocking picture hanger style so they can be taken down and used at any time.
cults3d
Wall-mount computer console for your vault. PRE-SUPPORTED For best results, it is advised that you use the best support and print settings for your own printer. As with all 3D prints, some finishing may be required. ... Support us on Patreon ->...
thingiverse
It is quite strong and has no problem supporting the heaviest of keyboard style computers I have on the wall, the Amiga 1200. The Apple IIC is a very close second, and for it's size is unbelievably heavy. ... If you're concerned, just use an...
thingiverse
I ran out of ~$15 wall mounts for monitors while upgrading my setup to a standing desk, so designed & printed one for the 4th monitor. ...Here it is.
thingiverse
...It is mounted to the wall using two #10 countersunk drywall screws. It has a small slot in the back for a 1/8" diameter speaker wire. If the model is super tiny when you open it up in the slicer, just change the scale from mm to cm (multiply by 10).
thingiverse
Here a wall mount base that I design for my desktop computer. I used Fusion 360 for this project. Seat of 184mm wide with five points for mounting screw. I used standard gips anchor to hold that on my wall. I printed this with **SAKATA PLA HR-870...
thingiverse
You will need 2 wall screws with anchors suitable for your wall and a 2" wide velcro strap to keep the computer safe and secure to the mount. Simple but effective way to hide the computer behind the screen and get it up off of a plan table where it...
thingiverse
A mount for a computer case switch. ...0.3mm nozzle & PLA
prusaprinters
I have set the majority of printed parts in a way to strengthen the mount.Mounting Hardware Required:4x M4x10 Cap Screws4x #10x1-½ Countersunk Screw (recommend using wall anchors for drywall)Order of Operations of text files converted back into...
thingiverse
In the customizer, you can enter the Length, width and height of any piece of gear that you need to wall-mount and the model will scale accordingly. If you need wiggle room, please account for that margin in your entry. ...Print Settings Printer Brand: ...
thingiverse
Designed these bad boys to hold up my computer - and they work. They are big for rigidity, not for strength. Requires 8xM5x25mm + 8xM5 Washers for the entire setup (4 each bracket). I tap the holes first but you don't have to - depending on the...
thingiverse
This Gardena EasyControl is meant to hang on the watertap but with this mount you can hang it everywhere. ...;-) It is a nice fit so print it at 100% infill to make it rugged.
thingiverse
Needed to get the computer case off the workbench so I built this to mount the computer against the wall. Should work fine with drywall anchors. Recommend using at least two under, and one above the computer. You can even strap between them with...
thingiverse
Nice way to display your classic computers.
thingiverse
I designed this 3D printable attachment that allows an AUKEY USB-C Hub 12-in-1 Hub to be mounted to the wall to free up desk space. Hub/Dock slides into the attachment and the attachment is designed to stick to the wall with Command large picture...
thingiverse
This thing is taller adds material on the bottom to compensate for the proper ATX motherboard mount height. Shims will have to be printed for the ATX backplane in order to make it tall enough. I think the shims need to be 3.19mm. ...I made this for...
prusaprinters
This is a mount for a 5 inch touchscreen I made this to go in the front of an alienware PC case I am restoring, but it should fit any PC with front bays for CD/DVD drives
thingiverse
A costume ITX mount to fit the motherboard on top pf it and still have some airflow beneath it. ... I designed this part as a part of my costume desk PC built.