wall mounted microphone arm 3d models

This wall mounted microphone arm is designed to hold the at2100 usb / xlr microphone. I designed this because my current microphone arm was always pushing down on my desk too hard, and it was also just getting in the way. This was my first time...

I made this to mount microphone arms to the wall to keep the desk less cluttered. Attach it to the wall with drywall screws or to a stud, then drop the arm in. ...The curved part should face the bottom.

This is a mount for a 1/2 " boom arm for a microphone to be mounted to a wall. ...I was having problems with my clamp breaking through my cheap desk, so I plan on just attaching it to the wall I have not gotten this to work yet even with 100% infill my...

Wall Mount for mounting your boom microphone on or making your own custom top down camera mount.

This is a parametric model of a wall mount for a microphone boom arm. I've been using it for the past 6 months with zero issues. The source code is freely available below if you want to generate the STL for free yourself, otherwise the ready to go...

This is a wallmount for the Microphone arm of my Marantz pod pack 1 microphone

Wall mount for articulated microphone arms, specifically the RODE PSA-1. The only manufactured one I could find was $25, had 3 holes, only 2 of which would fit on a single 2x4 stud. This wall mount is designed specifically for mounting to a stud,...

Wall mount for articulated microphone arms, specifically the RODE PSA-1. The only manufactured one I could find was $25, had 3 holes, only 2 of which would fit on a single 2x4 stud. This wall mount is designed specifically for mounting to a stud,...

... alongside the servo arm. The rotating platform was modified to make it stronger and a little easier to print and the middle link was modified to hold a smaller servo. I also added a wall mount so the whole thing can be easily mounted and removed.

Simple arms to screw on the wall, then use a simple rod between to hang your filament while printing. ...Print Settings Rafts: No Supports: ...

Simple arms to screw on the wall, then use a simple rod between to hang your filament while printing. Print Settings Rafts: No Supports: No Infill: 50% Category: 3D Printer Accessories

Microphone arm mounted on 20x40mm rectangular tube. Designed for Trust Starzz. Unfolded length: 21cm Supports need only in "microphone holder.stl" Enjoy! ...

Microphone arm adaptor, one side screw in for a tripod and the other for microphone accessorie.

I made this arm in FreeCAD, printerd with PLA, works well,you just need your own head for microphone.This head works with razer sieren mini.

I just designed the microphone arm, Part 1 and part 2 print with 40-60% padding but handle and hook with 100% padding. I used PLA but if someone wants a stronger print the ABS should be good. ...

The arms were drawn in two parts to be able to be printed on my Creality Ender 3. The 2 arms being identical, you can print each part twice in 1 time. For assembly you will need M5 screws and nuts, and one M6 screw and nut for fixing the stand to...

I once unmounded a microphone from gaming headset because headphones stopped working and I decided to make small arm for this microphone so I can put it on my desk. I designed it in Fusion 360 and it works great. If you decide to make this project...

I was surprised to see that nobody had designed a microphone mount for this articulated arm system. Since there was none, I decided to design one to fit most common mic mounts. ...Simple design, but effective.

Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print. Category: Audio

Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print.

quick model of microphone arm desk mount should fit most IKEA desks without any issues. ... test print out of PLA came out great, fits perfectly snug use with caution, no clamp, no warranty Materials needed: 2x M3 screw 8-22mm long 2x M3 nut 1x...

Extending microphone arm mount for the skadis pegboard system. Wanted something with minimal extra parts that should be doable without a hardware store visit. Still tweaking the design. ... Requires, MicMountSkadis x1 MicMount58 x1 MicMountArm...

Mount for attaching an adjustable microphone mount to a monitor mount. ...Specifically these two items: http://a.co/2HOoMSs http://a.co/chwYN3L

Microphone arm mount for ADSM302 or similar microscopes with up to 35mm in mount diameter. You will need: 3 x M3 square nuts 3 x M3x10 or similar screws 1 x M3x40 mm or similar screw These parts should be familiar to Prusa owners and will still be in...

Microphone arm mount for ADSM302 or similar microscopes with up to 35mm in mount diameter. You will need: 3 x M3 square nuts 3 x M3x10 or similar screws 1 x M3x40 mm or similar screw These parts should be familiar to Prusa owners and will...

This is a modular arm with sensor holder for wall mount. ... With this arm you can individual adjust the position of a sensor with M18 mount.

This is a 4 screw point wall mounted armed bracket for hanging a vietnam era practice bomb on your wall. Pretty specific eh? ... Fun having a 3d printer isn't it.

This is a 4 screw point wall mounted armed bracket for hanging a vietnam era practice bomb on your wall. Pretty specific eh? ... Fun having a 3d printer isn't it.

Dimensions (mm): 225x385, H360 Polys: 26 801 Verts: 26 914 File formats: 3ds max Corona, OBJ, FBX All preview images were rendered using Corona for 3ds max 2014...

I wanted to mount my microphone on a wall, so I designed this thing.