wall wire cover 3d models
395364 3d models found related to wall wire cover.thingiverse
Customizable cover box with open back & bottom for hiding an ugly wall plate/wiring/etc. Hangs from screws/nails above item to be covered (tick marks on top indicate nail positions). Recommend painting with wall color. ... [Updated 10/19/20:...
thingiverse
Wall mounting cover for two 20mm pipe. ...You can either print it as a single one or print it as split models and then super glue it.
prusaprinters
Wall mounting cover for two 20mm pipe. ...You can either print it as a single one or print it as split models and then super glue it.</p><h3>Print Settings</h3><p><strong>Printer Brand:</strong></p><p>Creality</p><p class="detail-setting...
thingiverse
Parametric cover for a holes you may drill for mains wires through table tops, cupboard walls and so on. The idea is that you may need a fairly big hole to enable the plug the go through. Which would leave a big, ugly and impractical hole, unless...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wire_hole_offset = 20.0 hole_dia = 77 t_starts = 1 have_lower_frame = 0 tol = 0.7 wall = 1.2 hole_depth = 9 wire_dia = 8 lip = 3 t_pitch = 1.75...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wall = 1.2 have_lower_frame = 1 t_pitch = 1.75 hole_depth = 23 framewall = 4.0 t_starts = 6 lip = 5.0 wire_dia = 12.0 wire_hole_offset = 20.0...
thingiverse
Customized version of http://www.thingiverse.com/thing:1324924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of http://www.thingiverse.com/thing:1324924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
connector box 2 pin din
thingiverse
Wire cover for running small cable or wire through a wall or cabinet. ...My intent is to use it on an RV to cover the outlet and seal with silicone on an antenna installation.
thingiverse
I designed this to cover a hole i drilled into the floor of my boat so that I could run a couple of wires into the boat but didnt want to leave a visible hole or allow water easily in. After printing, I added some marine sealant around edges to...
thingiverse
I needed a cover for the led-driver and wires in my spotlight installation came up with this. about 200 mm high, fits in my anycubic i3 Mega, but check the cabling from printhead at max height before printing... ... I printed with PLA Z at 0.2
thingiverse
... tape and attached it to the rug. It would work with wood too. I used around 140 g of PLA+ to cross my living room, much cheaper than commercial wire covers. ... Remix ideas: enlarge the surface or create an inner aperture to fit round cords.
prusaprinters
The connection wasn't that nice and I offered to design a nice cover. After a lot of trial and error, including learning OpenSCAD, I came up with this. You mount the base plate with some screws to the wall. The lamp fitting will fit in the large...
cults3d
... is a ceiling cover ideal for antique roses. ... Base diameter 75mm height 75mm Hole for cable clamp 10mm When no standard is the right size, here is an ideal ceiling cover for old rosettes. ... Base diameter 75mm height 75mm Hole for cable clamp 10mm
thingiverse
2 prong wire cover for extension cord. ...used a small nail to secure to the wall but could use double sided tape also