wanhao d6 makerselect ultimate silicone boot for heat block by 3d models

Tighten the M30 nuts firmly by grasping them securely on both sides of their respective threaded studs on the bottom rear of the equipment and turning clockwise with a wrench.

Adjustment Mechanism for Optimizing Z-Axis Scale

You can silence a piezo buzzer significantly by stuffing it with foam, resulting in a noticeable drop in decibel levels. However, this may require some fine-tuning to achieve an optimal fit. ...To get started, wrap your piezo buzzer in tape and then...

Frustrated with repeatedly monitoring my printer during use with a new roll of filament, I took action by crafting two discs to secure around the spool shafts. To prevent loose wrapping and jumping of the drum that leads to filament entanglement and...

I required a solution for streamlining resin extraction and vat sanitizing processes. ...This modification effectively tilts the vat to optimize syringe usage, eliminating the need for messy pouring.

I decided to create yet another set of Lack legs. ...One set is designed specifically for 3mm panels, while the other is tailored for use with 10mm materials.

A replacement backplate is now available for the Duplicator i3 to accommodate an 80mm fan seamlessly.

Distance for Fan Shroud Duplicator 6 Ensures Safe and Precise Separation

Here they are guys, the last feet you will ever need for your duplicator i3. ...:) NinjaFlex or similar flexible filament for these. ... Remember to support my work on: Instagram - Twitter- YouTube @webberen - THANKS!

I crafted a custom filament guide specifically designed for my trusty Monoprice Maker Select V2, perfect for situations where the spool is attached to the side of the machine.

This text will be used for bracket testing, allowing the creation of something amazing for the bracket, such as a filament roll holder. ... The Duplicator i3 third-rail Z tower bracket is featured here: http://www.thingiverse.com/thing:1234567

Here is a rewritten version of the original text: The entire assembly isn't needed; only the mount for the EZABL is required, specifically designed for use with RealRhen's Titan Aero mount.

A Simple Solution for a Cleaner Workspace. ...The printer is upgraded, and now the desk area looks much more organized.

This is the actual 3D of the authentic 3D for the resin tank of the Duplicator 7.

... models of mounts for both the right and left side of the build plate, depending on your preference. To install this mount, simply follow the installation instructions for my Glass Plate Holders, and the rest should be pretty self-explanatory.

This cable management system keeps USB, power, and network cables organized, designed specifically for the Duplicator/Maker Select but adaptable to any surface 1-2mm thick. I required this clip to route cables across my printer's top to my Raspberry...

Default thumbwheels on my i3 mini were extremely slick, prompting me to design and 3D print custom thumbwheels for improved grip and control.

The 3D model is the precise replica of the original 3D design intended for the resin vat of the Duplicator 7.

Here are my printing settings: Print Settings Rafts: No preference - you can go with or without Supports: Yes, for stability Resolution: Set this to 0.2 for medium quality Infill: 20% for balanced print strength and speed After the model comes off...

Once you move the spool holder from the gantry over to the table, it's likely that you'll require a filament guide. ...I've found this particular one to be extremely useful for my needs.

Good Printing for Everyone! ... **Print Settings** Everyone can enjoy good prints with the following settings: * **Rafts**: Turned off * **Supports**: Disabled * **Resolution**: Set to 0.3 mm * **Infill**: Filled to 100% density

The original plate didn't work well for me, as the hole was too small, and the lever was not aligned properly with the drive gear, so I made a new version and it works better for me. YMMV. This only works for the MK10 gear, I made a separate one for...

This extruder mounter is designed to work with the MGN12H and any e3d v6/vulcano or similar, for that use one or 2 spacers I use it with a fan 5015 at 24 volts, this is the fan adapter https://www.thingiverse.com/thing:2175956 Infill 40% supports...

This redesign uses the same 40mm centrifugal blower as the original SuperMagnum duct, but adds a lip inside the air box for the fan to sit on and a single 3mm screw mount. This design is printed with the bracket opening facing upwards, and supports...

... likely feel the same. To assemble, you need to have three .stl files: conus.stl (2x), disc.stl, and disc2.stl. For printing the conus.stl file, place it as directed on your 3D printer, as this should allow for a print without supports required.

... 2 mm and an infill percentage of at least 10%. Only the "Spool-80mm" requires supports due to its unique design. The spool holder currently accommodates spools up to 80mm in width, but future updates will introduce support for various other sizes.

It uses the same 40mm centrifugal blower as the original SuperMagnum duct, but has a lip inside the air box for the fan to sit on, and mount for a single 3mm screw. Obviously this is printed with the bracket opening pointed up, and supports turned...

... it was too big to fit the scraper on it after adding the z-brace extensions with an allen wrench extension. ...The attached images show the revised hook. I'm currently waiting for another print, but soon I'll add more photos of the completed print.

I'm setting up a basic webcam mount for my 3D printer right now and it's incredibly easy to do. All you have to do is clip this onto the front plate of the base. ...I happen to be using a Logitech C615, but any webcam with a standard 1/4" screw mount...

Here they are guys, the last feet you will ever need for your duplicator i3. ...:)\r\n\r\nNinjaFlex or similar flexible filament is what these require.\r\n\r\n<blockquote>\r\n<h5>\r\nSupport my work on: Instagram - Twitter- YouTube \r\n@webberen -...